| 전자부품 데이터시트 검색엔진 |
|
UCS1002-1 데이터시트(PDF) 60 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UCS1002-1 데이터시트(HTML) 60 Page - Microchip Technology |
|
60 / 116 page ![]() Programmable USB Port Power Controller with Charger Emulation Datasheet Revision 1.4 (07-16-13) 60 SMSC UCS1002 DATASHEET Chapter 9 Active State 9.1 Active State Overview The UCS1002 has the following modes of operation in the Active state: Data Pass-through, BC1.2 DCP, BC1.2 SDP, BC1.2 CDP, and Dedicated Charger Emulation Cycle. The current limiting mode depends on the Active mode behavior (see Table 9.2, "Current Limit Mode Options"). 9.2 Active Mode Selection The Active mode selection is controlled by three controls: EM_EN, M1, and M2, as shown in Table 9.1. Note 9.1 BC1.2 SDP behaves the same as the Data Pass-through mode with the exception that it is preceded by a VBUS discharge when the mode is entered per the BC1.2 specification. 9.3 BC1.2 Detection Renegotiation The BC1.2 specification allows a charger to act as an SDP, CDP, or DCP and to change between these roles. To force an attached portable device to repeat the charging detection procedure, VBUS must be cycled. In compliance with this specification, the UCS1002 automatically cycles VBUS when switching between the BC1.2 SDP, BC1.2 DCP, and BC1.2 CDP modes. 9.4 Data Pass-through (No Charger Emulation) When commanded to Data Pass-through mode, UCS1002 will close its USB high-speed data switch to allow USB communications between a portable device and host controller and will operate using trip current limiting. No charger emulation profiles are applied in this mode. Data Pass-through mode will persist until commanded otherwise by the M1, M2, and EM_EN controls. APPLICATION NOTE: If it is desired that the Data Pass-through mode operates as a traditional / standard port power switch, the S0 control should be set to ‘0’. When entering this mode, there is no automatic VBUS discharge. Table 9.1 Active Mode Selection # M1 M2 EM_EN ACTIVE MODE 1 0 0 1 Dedicated Charger Emulation Cycle 2 0 1 0 Data Pass-through 3 0 1 1 BC1.2 DCP 4 1 0 0 BC1.2 SDP - See Note 9.1 5 1 0 1 Dedicated Charger Emulation Cycle 6 1 1 0 Data Pass-through 7 1 1 1 BC1.2 CDP |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |