전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

MC68HC908AP16CFB 데이터시트(PDF) 60 Page - Motorola, Inc

부품명 MC68HC908AP16CFB
상세설명  Microcontrollers
PDF  440 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  MOTOROLA [Motorola, Inc]
홈페이지  http://www.freescale.com
Logo MOTOROLA - Motorola, Inc

MC68HC908AP16CFB 데이터시트(HTML) 60 Page - Motorola, Inc

Back Button MC68HC908AP16CFB Datasheet HTML 56Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 57Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 58Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 59Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 60Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 61Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 62Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 63Page - Motorola, Inc MC68HC908AP16CFB Datasheet HTML 64Page - Motorola, Inc Next Button
Zoom Inzoom in Zoom Outzoom out
 60 / 440 page
background image
FLASH Memory
Data Sheet
MC68HC908AP Family — Rev. 2.5
60
MOTOROLA
4.6 FLASH Program Operation
Programming of the FLASH memory is done on a row basis. A row
consists of 64 consecutive bytes starting from addresses $XX00,
$XX40, $XX80 or $XXC0. Use the following procedure to program a row
of FLASH memory. (Figure 4-3 shows a flowchart of the programming
algorithm.)
1. Set the PGM bit. This configures the memory for program
operation and enables the latching of address and data for
programming.
2. Write any data to any FLASH location within the address range of
the row to be programmed.
3. Wait for a time, tnvs (5 µs).
4. Set the HVEN bit.
5. Wait for a time, tpgs (10 µs).
6. Write data to the FLASH location to be programmed.
7. Wait for time, tprog (20 µs to 40 µs).
8. Repeat steps 6 and 7 until all bytes within the row are
programmed.
9. Clear the PGM bit.
10. Wait for time, tnvh (5 µs).
11. Clear the HVEN bit.
12. After time, trcv (1 µs), the memory can be accessed in read mode
again.
This program sequence is repeated throughout the memory until all data
is programmed.
NOTE:
The time between each FLASH address change (step 6 to step 6), or the
time between the last FLASH addressed programmed to clearing the
PGM bit (step 6 to step 9), must not exceed the maximum programming
time, tprog max.
NOTE:
Programming and erasing of FLASH locations cannot be performed by
code being executed from the FLASH memory. While these operations
must be performed in the order shown, other unrelated operations may
occur between the steps.
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com