| 전자부품 데이터시트 검색엔진 |
|
VSC8658 데이터시트(PDF) 88 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
VSC8658 데이터시트(HTML) 88 Page - Microsemi Corporation |
|
88 / 95 page ![]() Pin Descriptions VMDS-10242 VSC8658 Datasheet Revision 4.1 80 7.2.8 Miscellaneous The following table lists pins not associated with a particular interface or facility on the device. Table 90 • Miscellaneous Pins Pin Name Type Description H25 J24 J25 J26 K24 K25 K26 L24 CMODE7 CMODE6 CMODE5 CMODE4 CMODE3 CMODE2 CMODE1 CMODE0 IA Configuration mode (CMODE) pins. For more information, see CMODE, page 55. J1 XTAL1/REFCLK I Crystal oscillator input. If OSCEN=high then a 25 MHz parallel resonant crystal with +/–50 ppm frequency tolerance should be connected across XTAL1 and XTAL2. A 33 pF capacitor should also tie the XTAL1 pin to ground. Reference clock input. If OSCEN=low, the clock input frequency can either be 25 MHz (PLLMODE=0) or 125 MHZ (PLLMODE is high). J2 XTAL2 OCRYST Crystal oscillator output. The crystal should be connected across XTAL1 and XTAL2. A 33 pF capacitor should also tie the XTAL2 pin to ground. If not using a crystal oscillator, this output pin can be left floating if driving XTAL1/REFCLK with a reference clock. R2 OSCEN IPD Oscillator enable. This pin is sampled on the rising edge of NRESET. If HIGH, then the on-chip oscillator circuit is enabled. If low (or left floating), the oscillator circuit is disabled and the device must be supplied with a 25 MHz or 125 MHz reference clock to the REFCLK pin R1 PLLMODE IPD PLL mode input select. Sampled on power-up or reset. If PLLMODE is low, then REFCLK must be 25 MHz. If PLLMODE is high, then REFCLK must be 125 MHz. J3 J4 K3 K4 L1 L2 M1 M2 L3 L4 M3 M4 P3 P4 R3 R4 T23 T24 R23 R24 P23 P24 N23 N24 P25 P26 N25 N26 M25 M26 L25 L26 LED[3:0]_7 LED[3:0]_6 LED[3:0]_5 LED[3:0]_4 LED[3:0]_3 LED[3:0]_2 LED[3:0]_1 LED[3:0]_0 O LED direct-drive outputs. All LEDs pins are active- low. A serial LED stream can also be implemented. For more information about LED operation, see LED Mode Select, page 43. F23 REF_REXT_A ABIAS Reference external connects to an external 2 K Ω (1%) resistor to analog ground. E23 REF_FILT_A ABIAS Reference filter connects to an external 1 µF capacitor to analog ground. F4 REF_REXT_B ABIAS Reference external connects to an external 2 K Ω (1%) resistor to analog ground. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |