SST26VF032B-104ISLASHSM datasheet(11/82 Pages) MICROCHIP

11 / 82 page

 2013-2022 Microchip Technology Inc. and its subsidiaries

DS20005218K-page 11

SST26VF032B/SST26VF032BA

4.5.1

WRITE ENABLE LATCH (WEL)

The Write Enable Latch (WEL) bit indicates the status

of the internal memory’s Write Enable Latch. If the WEL

bit is set to ‘1’, the device is write enabled. If the bit is

set to ‘0’ (reset), the device is not write enabled and

does not accept any memory program or erase, Protec-

tion Register Write, or Lock-Down commands. The

Write-Enable Latch bit is automatically reset under the

following conditions:

• Power-up

• Reset

• Write Disable (WRDI) instruction

• Page Program instruction completion

• Sector Erase instruction completion

• Block Erase instruction completion

• Chip Erase instruction completion

• Write Block Protection register instruction

• Lock-Down Block Protection register instruction

• Program Security ID instruction completion

• Lockout Security ID instruction completion

• Write Suspend instruction

• SPI Quad Page program instruction completion

• Write STATUS Register

4.5.2

WRITE SUSPEND ERASE STATUS

(WSE)

The Write Suspend Erase status (WSE) indicates when

an erase operation has been suspended. The WSE bit

is ‘1’ after the host issues a suspend command during

an Erase operation. Once the suspended Erase

resumes, the WSE bit is reset to ‘0’.

4.5.3

WRITE SUSPEND PROGRAM

STATUS (WSP)

The Write Suspend Program status (WSP) bit indicates

when a Program operation has been suspended. The

WSP is ‘1’ after the host issues a suspend command

during the Program operation. Once the suspended

Program resumes, the WSP bit is reset to ‘0’.

4.5.4

WRITE PROTECTION LOCK-DOWN

STATUS (WPLD)

The Write Protection Lock-Down status (WPLD) bit

indicates when the Block Protection register is locked-

down to prevent changes to the protection settings.

The WPLD is ‘1’ after the host issues a Lock-Down

Block Protection command. After a power cycle, the

WPLD bit is reset to ‘0’.

4.5.5

SECURITY ID STATUS (SEC)

The Security ID Status (SEC) bit indicates when the

Security ID space is locked to prevent a Write com-

mand. The SEC is ‘1’ after the host issues a Lockout

SID command. Once the host issues a Lockout SID

command, the SEC bit can never be reset to ‘0.’

4.5.6

BUSY

The BUSY bit determines whether there is an internal

Erase or Program operation in progress. If the BUSY

bit is ‘1’, the device is busy with an internal Erase or

Program operation. If the bit is ‘0’, no Erase or Program

operation is in progress.

4.5.7

CONFIGURATION REGISTER

The Configuration register is a Read/Write register that

stores a variety of configuration information. See

Table 4-3 for the function of each bit in the register.

TABLE 4-3:

CONFIGURATION REGISTER

Bit

Name

Function

Default at Power-up

Read/Write (R/W)

0RES

Reserved

1IOC

I/O Configuration for SPI Mode

1 = WP# and HOLD# pins disabled

0 = WP# and HOLD# pins enabled

0(1)

R/W

2RES

Reserved

BPNV

Block Protection Volatility State

1 = No memory block has been permanently locked

0 = Any block has been permanently locked

4RES

Reserved

5RES

Reserved

6RES

Reserved

7WPEN

Write Protection Pin (WP#) Enable

1 = WP# enabled

0 = WP# disabled

0(2)

R/W

Note 1: SST26VF032B default at Power-up is ‘0’. SST26VF032BA default at Power-up is ‘1’.

2: Factory default setting. This is a nonvolatile bit; default at power-up will be the setting prior to power-down.

SST26VF032B-104I/SM 데이터시트(PDF) 11 Page - Microchip Technology

SST26VF032B-104I/SM 데이터시트(HTML) 11 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82

데이터시트 다운로드

링크 URL