| 전자부품 데이터시트 검색엔진 |
|
RIVA128 데이터시트(PDF) 30 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
RIVA128 데이터시트(HTML) 30 Page - STMicroelectronics |
|
30 / 77 page ![]() 128-BIT 3D MULTIMEDIA ACCELERATOR RIVA 128 30/77 Table 5. Truth table of supported SGRAM commands NOTES 1 FBCKE is high and DSF is low for all supported commands. 2 Activates or deactivates FBD[127:0] during writes (zero clock delay) and reads (two-clock delay). 6.1 SGRAM INITIALIZATION SGRAMs must be powered-up and initialized in a predefined manner. The first SGRAM command is reg- istered on the first clock edge following PCIRST# inactive. All internal SGRAM banks are precharged to bring the device(s) into the “all bank idle” state. The SGRAM mode registers are then programmed and loaded to bring them into a defined state before performing any operational command. 6.2 SGRAM MODE REGISTER The Mode register defines the mode of operation of the SGRAM. This includes burst length, burst type, read latency and SGRAM operating mode. The Mode register is programmed via the Load Mode register and retains its state until reprogrammed or power-down. Mode register bits M[2:0] specify the burst length; for the RIVA 128 SGRAM interface these bits are set to zero, selecting a burst length of one. In this case FBA[7:0] select the unique column to be accessed and Mode register bit M[3] is ignored. Mode register bits M[6:4] specify the read latency; for the RIVA 128 SGRAM interface these bits are set to either 2 or 3, selecting a burst length of 2 or 3 respectively. Command1 FBCSx FBRAS# FBCAS# FBWE# FBDQM FBA[9:0] FBD[63:0] Notes Command inhibit (NOP) H xxxx x x No operation (NOP) L H H H x x x Active (select bank and activate row) LL H H x FBA[9]=bank FBA[8:0]=row x Read (select bank and column and start read burst) LH LH x FBA[9]=bank FBA[8]=0 FBA[7:0]=row x Write (select bank and column and start write burst) LH L L x FBA[9]=bank FBA[8]=0 FBA[7:0]=row valid data Precharge (deactivate row in both banks) LL H L x FBA[8]=1 x Load mode register L LLL x FBA[8:0] = opcode Write enable/output enable ---- L - active 2 Write inhibit/output High-Z ---- H - high-Z 2 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |