ATmega162 datasheet(86/324 Pages) ATMEL

86 / 324 page

2513K–AVR–07/09

ATmega162/V

General Interrupt

Control Register –

GICR

• Bit 7 – INT1: External Interrupt Request 1 Enable

When the INT1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-

nal pin interrupt is enabled. The Interrupt Sense Control1 bits 1/0 (ISC11 and ISC10) in the MCU

general Control Register (MCUCR) define whether the external interrupt is activated on rising

and/or falling edge of the INT1 pin or level sensed. Activity on the pin will cause an interrupt

request even if INT1 is configured as an output. The corresponding interrupt of External Interrupt

Request 1 is executed from the INT1 Interrupt Vector.

• Bit 6 – INT0: External Interrupt Request 0 Enable

When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-

nal pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the MCU

general Control Register (MCUCR) define whether the external interrupt is activated on rising

and/or falling edge of the INT0 pin or level sensed. Activity on the pin will cause an interrupt

request even if INT0 is configured as an output. The corresponding interrupt of External Interrupt

Request 0 is executed from the INT0 Interrupt Vector.

• Bit 5 – INT2: External Interrupt Request 2 Enable

When the INT2 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-

nal pin interrupt is enabled. The Interrupt Sense Control2 bit (ISC2) in the Extended MCU

Control Register (EMCUCR) defines whether the external interrupt is activated on rising or fall-

ing edge of the INT2 pin. Activity on the pin will cause an interrupt request even if INT2 is

configured as an output. The corresponding interrupt of External Interrupt Request 2 is executed

from the INT2 Interrupt Vector.

• Bit 4 – PCIE1: Pin Change Interrupt Enable 1

When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin

change interrupt 1 is enabled. Any change on any enabled PCINT15..8 pin will cause an inter-

rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI1

Interrupt Vector. PCINT15..8 pins are enabled individually by the PCMSK1 Register.

• Bit 3 – PCIE0: Pin Change Interrupt Enable 0

When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin

change interrupt 0 is enabled. Any change on any enabled PCINT7..0 pin will cause an interrupt.

The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0 Interrupt

Vector. PCINT7..0 pins are enabled individually by the PCMSK0 Register.

Bit

654

INT1

INT0

INT2

PCIE1

PCIE0

–

IVSEL

IVCE

GICR

Read/Write

R/W

Initial Value

ATmega162 데이터시트(PDF) 86 Page - ATMEL Corporation

ATmega162 데이터시트(HTML) 86 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL