MPC8347VRAGDB datasheet(75/99 Pages) FREESCALE

75 / 99 page

MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 12

Freescale Semiconductor

Package and Pin Listings

LVDD1

U20, W25

Power for

three-speed

Ethernet #1

and for

Ethernet

management

interface I/O

(2.5 V, 3.3 V)

LVDD1—

LVDD2

V20, Y23

Power for

three-speed

Ethernet #2

I/O (2.5 V,

3.3 V)

LVDD2—

VDD

J11, J12, J15, K10, K11, K12, K13,

K14, K15, K16, K17, K18, K19, L10,

L11, L18, L19, M10, M19, N10, N19,

P9, P10, P19, R10, R19, R20, T10,

T19, U10, U19, V10, V11, V18, V19,

W11, W12, W13, W14, W15, W16,

W17, W18

Power for core

(1.2 V)

VDD

—

OVDD

B27, D3, D11, D19, E15, E23, F5, F8,

F11, F14, F17, F20, G24, H23, H24,

J6, J14, J17, J18, K4, L9, L20, L23,

L25, M6, M9, M20, P5, P20, P23, R6,

R9, R24, U23, V4, V6

PCI, 10/100

Ethernet, and

other standard

(3.3 V)

OVDD

—

MVREF1

AF19

DDR

reference

voltage

—

MVREF2

AE10

DDR

reference

voltage

—

No Connection

V1, V2, V5

—

Notes:

1. This pin is an open-drain signal. A weak pull-up resistor (1 k

Ω) should be placed on this pin to OV

DD.

2. This pin is an open-drain signal. A weak pull-up resistor (2–10 k

Ω) should be placed on this pin to OV

DD.

3. During reset, this output is actively driven rather than three-stated.

4. These JTAG pins have weak internal pull-up P-FETs that are always enabled.

5. This pin should have a weak pull-up if the chip is in PCI host mode. Follow the PCI specifications.

6. This pin must always be tied to GND.

7. This pin must always be left not connected.

8. Thermal sensitive resistor.

9. It is recommended that MDIC0 be tied to GRD using an 18

Ω resistor and MDIC1 be tied to DDR power using an 18 Ω resistor.

10.TSEC1_TXD[3] is required an external pull-up resistor. For proper functionality of the device, this pin must be pulled up or

actively driven high during a hard reset. No external pull-down resistors are allowed to be attached to this net.

11. A weak pull-up resistor (2–10 k

Ω) should be placed on this pin to LV

DD1.

12. For systems that boot from local bus (GPCM)-controlled NOR flash, a pullup on LGPL4 is required.

Table 56. MPC8347EA (PBGA) Pinout Listing (continued)

Signal

Package Pin Number

Pin Type

Power

Supply

Notes

MPC8347VRAGDB 데이터시트(PDF) 75 Page - Freescale Semiconductor, Inc

MPC8347VRAGDB 데이터시트(HTML) 75 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99

데이터시트 다운로드

링크 URL