| 전자부품 데이터시트 검색엔진 |
|
MCP8026 데이터시트(PDF) 48 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP8026 데이터시트(HTML) 48 Page - Microchip Technology |
|
48 / 64 page ![]() MCP8025/6 DS20005339B-page 48 2016 Microchip Technology Inc. 5.0 APPLICATION INFORMATION 5.1 Component Calculations 5.1.1 CHARGE PUMP CAPACITORS FIGURE 5-1: Charge Pump. Let: 5.1.1.1 Flying Capacitor The flying capacitor should be chosen to charge to a minimum of 95% (3 ) of VDDH within one half of a switching cycle. Choose a 180 nF capacitor. 5.1.1.2 Charge Pump Output Capacitor Solve for the charge pump output capacitance, connected between V12P and ground, that will supply the 20 mA load for one switch cycle. The +12V LDO pin on the MCP8025/6 is the “V12P” pin referenced in the calculations. For stability reasons, the +12V LDO and +5V LDO capacitors must be greater than 4.7 µF, so choose C 4.7 µF. 5.1.1.3 Charging Path (Flying Capacitor across CAP1 and CAP2) 5.1.1.4 Transfer Path (Flying and Output Capacitors) 5.1.1.5 Calculate the Flying Capacitor Voltage Drop in One Cycle while Supplying 20 mA The second and subsequent transfer cycles will have a higher voltage available for transfer, since the capacitor is not completely depleted with each cycle. VCAP will then be VCAP – dV after the first transfer, plus VDDH –(VCAP – dV) times the RC constant. This repeats for each subsequent cycle, allowing a larger charge pump capacitor to be used if the system tolerates several charge transfers before requiring full-output voltage and current. Repeating the steps in Section 5.1.1.3, Charging Path (Flying Capacitor across CAP1 and CAP2) for the second cycle (and subsequent by re-calculating for each new value of VCAP after each transfer): 5.1.1.6 Charge Pump Results The maximum charge pump flying capacitor value is 202 nF to maintain a 95% voltage transfer ratio on the first charge pump cycle. Larger capacitor values may be used but they will require more cycles to charge to maximum voltage. The minimum required output capacitor value is 2.65 µF to supply 20 mA for 13.3 µs with a 100 mV drop. A larger output capacitor may be used to cover losses due to capacitor tolerance over temperature, capacitor dielectric and PCB losses. IOUT =20 mA fCP = 75 kHz (charge/discharge in one cycle) 50% duty cycle VDDH = 6V (worst case) RDSON =7.5 (RPMOS), 3.5 (RNMOS) V12P = 2 x VDDH (ideal) CESR =20 m (ceramic capacitors) VDROP =100 mV (VOUT ripple) TCHG =TDCHG = 0.5 x 1/75 kHz = 6.67 µs 3x =TCHG =TCHG/3 RC = TCHG/3 C= TCHG/(R x 3) C = 6.67 µs/([7.5 +3.5 +0.02]x 3) C = 202 nF C= IOUT x dt/dV C= IOUT x13.3 µs/(VDROP +IOUT xCESR) C = 20 mA x 13.3 µs/(0.1V + 20 mA x 20 m ) C 2.65 µF Transfer Charge VCAP =VDDH (1 – e-T/) VCAP = 6V (1–e – [6.67 µs/([7.5 +3.5 +20 m] x 180 nF)]) VCAP = 5.79V available for transfer V12P = VDDH +VCAP –IOUT x dt/C V12P = 6V + 5.79V – (20 mA x 6.67 µs/180 nF) V12P = 11.049V dV = IOUT x dt/C dV = 20 mA x 6.67 µs/180 nF dV = 0.741V @ 20 mA VCAP =(VCAP –dV) +(VDDH –(VCAP –dV)) (1 – e-T/) VCAP = (5.79V – 0.741V) + (6V – (5.79V – 0.741V) x (1–e – [6.67 µs/([7.5 +3.5 +20 m]x 180 nF)]) VCAP = 5.049V + 0.951V x 0.96535 VCAP = 5.967V available for transfer on second cycle |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |