SPC564A80L7 datasheet(86/157 Pages) STMICROELECTRONICS

86 / 157 page

Electrical characteristics

SPC564A74L7, SPC564A80B4, SPC564A80L7

86/157

Doc ID 15399 Rev 9

As a general rule, the value obtained on a single-layer board is within the normal range for

the tightly packed printed circuit board. The value obtained on a board with the internal

planes is usually within the normal range if the application board has:

●

One oz. (35 micron nominal thickness) internal planes

●

Components are well separated

●

Overall power dissipation on the board is less than 0.02 W/cm2

The thermal performance of any component depends on the power dissipation of the

surrounding components. In addition, the ambient temperature varies widely within the

application. For many natural convection and especially closed box applications, the board

temperature at the perimeter (edge) of the package is approximately the same as the local

air temperature near the device. Specifying the local ambient conditions explicitly as the

board temperature provides a more precise description of the local ambient conditions that

determine the temperature of the device.

At a known board temperature, the junction temperature is estimated using the following

equation:

Equation 2 TJ = TB + (RJB * PD)

where:

TB = board temperature for the package perimeter (

oC)

RJB = junction-to-board thermal resistance (

oC/W) per JESD51-8S

PD = power dissipation in the package (W)

When the heat loss from the package case to the air does not factor into the calculation, an

acceptable value for the junction temperature is predictable. Ensure the application board is

similar to the thermal test condition, with the component soldered to a board with internal

planes.

The thermal resistance is expressed as the sum of a junction-to-case thermal resistance

plus a case-to-ambient thermal resistance:

Equation 3 RJA = RJC + RCA

where:

RJA = junction-to-ambient thermal resistance (

oC/W)

RJC = junction-to-case thermal resistance (

oC/W)

RCA = case to ambient thermal resistance (

oC/W)

RJC is device related and is not affected by other factors. The thermal environment can be

controlled to change the case-to-ambient thermal resistance, RCA. For example, change

the air flow around the device, add a heat sink, change the mounting arrangement on the

printed circuit board, or change the thermal dissipation on the printed circuit board

surrounding the device. This description is most useful for packages with heat sinks where

90% of the heat flow is through the case to heat sink to ambient. For most packages, a

better model is required.

A more accurate two-resistor thermal model can be constructed from the junction-to-board

thermal resistance and the junction-to-case thermal resistance. The junction-to-case

thermal resistance describes when using a heat sink or where a substantial amount of heat

is dissipated from the top of the package. The junction-to-board thermal resistance

describes the thermal performance when most of the heat is conducted to the printed circuit

SPC564A80L7 데이터시트(PDF) 86 Page - STMicroelectronics

SPC564A80L7 데이터시트(HTML) 86 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL