| 전자부품 데이터시트 검색엔진 |
|
AM79C978AVCW 데이터시트(PDF) 157 Page - Advanced Micro Devices |
|
|
|||||||||||||||||||||||||||||
AM79C978AVCW 데이터시트(HTML) 157 Page - Advanced Micro Devices |
|
157 / 256 page ![]() Am79C978A 157 Table 38. PHY Select Programming These bits are read accessible al- ways, these bits can only be writ- ten from the EEPROM unless a write-enable bit, BCR2[13], is set. PHYSEL [1:0] is cleared by H_RESET and is not affected by S_RESET or STOP. 2-0 LINBC Reserved locations. These bits are read accessible always; write accessible only when either the STOP or the SPND bit is set. Af- ter H_RESET, the value in these bits will be 001b. The setting of these bits have no effect on any Am79C978A controller’s func- tion. LINBC is not affected by S_RESET or STOP. BCR19: EEPROM Control and Status Bit Name Description 31-16 RES Reserved locations. Written as zeros and read as undefined. 15 PVALID EEPROM Valid status bit. This bit is read accessible only. PVALID is read only; write operations have no effect. A value of 1 in this bit indicates that a PREAD opera- tion has occurred, and that (1) there is an EEPROM connected to the Am79C978A controller in- terface pins and (2) the contents read from the EEPROM have passed the checksum verification operation. A value of 0 in this bit indicates a failure in reading the EEPROM. The checksum for the entire 82 bytes of EEPROM is incorrect or no EEPROM is connected to the interface pins. PVALID is set to 0 during H_RESET and is unaffected by S_RESET or the STOP bit. How- ever, following the H_RESET op- eration, an automatic read of the EEPROM will be performed. Just as it is true for the normal PREAD command, at the end of this auto- matic read operation the PVALID bit may be set to 1. Therefore, H_RESET will set the PVALID bit to 0 at first, but the automatic EE- PROM read operation may later set PVALID to a 1. If PVALID becomes 0 following an EEPROM read operation (either automatically generated after H_RESET, or requested through PREAD), then all EEPROM-pro- grammable BCR locations will be reset to their H_RESET values. The content of the Address PROM locations, however, will not be cleared. If no EEPROM is present at the EESK, EEDI, and EEDO pins, then all attempted PREAD commands will terminate early and PVALID will not be set. This applies to the automatic read of the EEPROM after H_RESET, as well as to host- initiated PREAD commands. 14 PREAD EEPROM Read command bit. When this bit is set to a 1 by the host, the PVALID bit (BCR19, bit 15) will immediately be reset to a 0, and then the Am79C978A con- troller will perform a read opera- tion of 82 bytes from the EEPROM through the interface. The EEPROM data that is fetched during the read will be stored in the appropriate internal registers on board the controller. Upon completion of the EEPROM read operation, the Am79C978A controller will assert the PVALID bit. EEPROM contents will be in- directly accessible to the host through read accesses to the Ad- dress PROM (offsets 0h through Fh) and through read accesses to other EEPROM programmable registers. Note that read access- es from these locations will not actually access the EEPROM it- self, but instead will access the Am79C978A internal copy of the EEPROM contents. Write PHYSEL [1:0] Mode 00 Expansion ROM/Flash 01 EADI/Internal MII Snoop 10 Reserved 11 Reserved |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |