| 전자부품 데이터시트 검색엔진 |
|
HMS91C8032 데이터시트(PDF) 66 Page - Hynix Semiconductor |
|
|
|||||||||||||||||||||||||||||
HMS91C8032 데이터시트(HTML) 66 Page - Hynix Semiconductor |
|
66 / 157 page ![]() HMS91C8032/97C8032 NOV., 2001 Ver 1.02 63 SIO2TS flag turning to 0. This means that correct data setting and reading may fail if data setting or data reading is executed to the serial buffer during the wait canceled state. See Precautions in data setting and data reading section. Writing of 0 to SIO2TS flag during the wait cancel state causes the wait state to be estab- lished. This is called as “forced wait”. An example of wait operation is shown below. When wait is canceled, the serial data is output at the falling edge of the next clock, and the flag turns into the wait canceled state. When eight shift clock pulses are entered, the value of the output latch (usually high level) is output from the shift clock pin, and this causes the operation of the clock counter and serial buffer to be stopped. Note that correct data will not be set if data writing to and data reading from the serial buffer are attempted while the wait is in the canceled state and the shift clock pin is at high level. If data is written into the serial buffer while the wait is in the can- celed state and the shift clock pin is at low level, the content of MSB will be output to the serial data output pin at the time when MOV instruction is executed. If forced wait is effected during the wait canceled state, a wait state is resumed upon writing of 0 into SIO2TS flag. Usage of SIO1 and SIO2 Figure 4-25 and Figure 4-26 shows the input/output blocks and communication method of the SIO. As shown in Figure 4-25 and Figure 4-26, there are internal clock operation mode and external clock operation mode, and each mode permits transmission and reception. Master and slave operation modes are selected by SIOxCK1 and SIOxCK0 flags. Reception and transmission are set according to the pins used. In the master operation mode, SCK pin outputs internal clock. In this case, however, the SCK pin must be set as output port. In the slave operation mode, SCK pin is set in the floating state for receiving external clock. In this case, however, the SCK pin must be set as input port. Serial data is out- put from SO pin at the falling edge of the shift clock irrespective of the internal clock or external clock. In this case, however, SO pin must be set as output port, and SIO2HIZ flag be set. Serial data is input to the serial buffer as the status of SI pin at the rising edge of the shift clock irrespective of the internal clock or exter- nal clock. SCK pin reads the current status of output latch during a wait , or reads the status of the current pin during a wait cancel. SO pin reads the current status of output latch. Figure 4-24 Example of Wait Operation 0 12 3 78 0 D7 D6 D5 D1 D0 12 3 78 Wait cancel Wait Shift Clock Serial Data Clock Counter D7 D6 D5 D1 D0 Serial Output SIO2TS flag Wait canceled state Wait state Wait state Content of output latch Previous value |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |