TMP320C2811PBKA datasheet(100/147 Pages) TI

100 / 147 page

Electrical Specifications

100

June 2004

SPRS257

6.16 Event Manager Interface

6.16.1 PWM Timing

PWM refers to all PWM outputs on EVA and EVB.

Table 6−12. PWM Switching Characteristics†‡

PARAMETER

TEST CONDITIONS

MIN

MAX

UNIT

tw(PWM)§

Pulse duration, PWMx output high/low

td(PWM)XCO

Delay time, XCLKOUT high to PWMx output switching

XCLKOUT = SYSCLKOUT/4

† See the GPIO output timing for fall/rise times for PWM pins.

‡ PWM pin toggling frequency is limited by the GPIO output buffer switching frequency (20 MHz).

§ PWM outputs may be 100%, 0%, or increments of tc(HCO) with respect to the PWM period.

Table 6−13. Timer and Capture Unit Timing Requirements¶#

MIN

MAX

UNIT

Pulse duration TDIRx low/high

Without input qualifier

2 * tc(SCO)

cycles

tw(TDIR)

Pulse duration, TDIRx low/high

With input qualifier

1 * tc(SCO) + IQT||

cycles

Pulse duration CAPx input low/high

Without input qualifier

2 * tc(SCO)

cycles

tw(CAP)

Pulse duration, CAPx input low/high

With input qualifier

1 * tc(SCO) + IQT||

cycles

tw(TCLKINL)

Pulse duration, TCLKINx low as a percentage of TCLKINx cycle time

tw(TCLKINH)

Pulse duration, TCLKINx high as a percentage of TCLKINx cycle time

tc(TCLKIN)

Cycle time, TCLKINx

4 * tc(HCO)

¶ The QUALPRD bit field value can range from 0 (no qualification) through 0xFF (510 SYSCLKOUT cycles). The qualification sampling period is

2n SYSCLKOUT cycles, where “n” is the value stored in the QUALPRD bit field. As an example, when QUALPRD = 1, the qualification sampling

period is 1 x 2 = 2 SYSCLKOUT cycles (i.e., the input is sampled every 2 SYSCLKOUT cycles). Six such samples will be taken over five sampling

windows, each window being 2n SYSCLKOUT cycles. For QUALPRD = 1, the minimum width that is needed is 5 x 2 = 10 SYSCLKOUT cycles.

However, since the external signal is driven asynchronously, a 11-SYSCLKOUT-wide pulse ensures reliable recognition.

# Maximum input frequency to the QEP = min[HSPCLK/2, 20 MHz]

|| Input Qualification Time (IQT) = [5 x QUALPRD x 2] * tc(SCO)

tw(PWM)

td(PWM)XCO

PWMx

XCLKOUT†

† XCLKOUT = SYSCLKOUT

Figure 6−13. PWM Output Timing

XCLKOUT†

tw(TDIR)

TDIRx

† XCLKOUT = SYSCLKOUT

Figure 6−14. TDIRx Timing

TMP320C2811PBKA 데이터시트(PDF) 100 Page - Texas Instruments

TMP320C2811PBKA 데이터시트(HTML) 100 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL