PC87591L datasheet(91/437 Pages) NSC

91 / 437 page

Embedded Controller Modules (Continued)

Revision 1.07

www.national.com

4.2.6

Operation Modes

The DMAC operates in three different block transfer modes - single transfer, double buffer and auto-initialize. Select the ap-

propriate mode according to the character of the block transfer.

Single Transfer Operation

This mode provides the simplest way to accomplish a single block data transfer.

Initialization

1. Write the two block transfer addresses and byte count into the corresponding ADCAn, ADCBn and BLTCn counters, re-

spectively. The BLTCn counter should be written last.

2. Program the OT bit for Non-Auto-Initialize mode, and clear EOVR bit in DMACNTLn register to 0. Clear to 0 VLD bit in

DMASTATn register.

3. Set CHEN bit in DMACNTLn register to 1; the channel activates and responds to DMAC transfer requests.

Termination

When the BLTCn counter reaches 0:

●

The transfer operation terminates.

●

TC bit in DMASTATn register is set to 1, and CHAC is cleared to 0.

●

A level interrupt is generated (if enabled by ETC bit in DMACNTLn register).

Double Buffer Operation

This mode allows the software to set up the next block transfer specification while the current block transfer proceeds. This

mode is used for preparing the next buffer for use in a multi-buffer operation (e.g., the alternate buffer in a double-buffer

scheme).

Initialization

1. Write the two block transfer addresses and byte count into the ADCAn, ADCBn and BLTCn counters, respectively. The

BLTCn counter should be written last.

2. Program OT bit in DMACNTLn register for Non-Auto-Initialize mode.

3. Set CHEN bit in DMACNTLn register to 1; the channel activates and responds to DMAC transfer requests.

4. While the current block transfer proceeds, write the addresses and byte count for the next block into the ADRAn, ADRBn

and BLTRn registers. The BLTRn register should be written last.

Continuation / Termination

When the BLTCn counter reaches 0:

●

TC bit in DMASTATn register is set to 1.

●

A level interrupt is generated (if enabled by ETC bit in DMACNTLn register).

●

The DMAC channel checks the value of VLD bit.

If VLD bit is 1:

●

The channel copies the ADRAn, ADRBn and BLTRn values into ADCAn, ADCBn and BLTCn. The BLTCn counter

should be written last.

●

Clears VLD bit to 0.

●

Becomes ready to start the next block transfer (on the next DMA request).

If VLD bit is 0:

●

The transfer operation terminates.

●

The channel sets OVR bit in DMASTATn register to 1.

●

Clears CHAC bit to 0.

●

A level interrupt is generated (if enabled by EOVR bit in DMACNTLn register).

Note:

ADCB and ADRBn are used only in indirect (memory-to-memory) transfer. In Direct (Fly-By) mode, the DMAC does not use

them and therefore does not copy ADRBn into ADCBn.

PC87591L 데이터시트(PDF) 91 Page - National Semiconductor (TI)

PC87591L 데이터시트(HTML) 91 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL