| 전자부품 데이터시트 검색엔진 |
|
ML7396AB 데이터시트(PDF) 63 Page - LAPIS Semiconductor Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
ML7396AB 데이터시트(HTML) 63 Page - LAPIS Semiconductor Co., Ltd. |
|
63 / 140 page ![]() FEDL7396A/B/E-07 ML7396A/B/E 63/140 Interrupt generation timing In each interrupt generation, timing from reference point to interrupt interrupt generation (nitification) are described in the following table. Timeout procedure for interrupt notification waiting, are also described below. [Note] (1)The values are decribed in units of “symbol time” in the below table is the value at 100kbps. If using other data, please use 20, 5, and 2.5 for 50kbps, 200kbps, and 400kbps, respectively. (2)Below table uses the following format of TX/RX data. 24 byte (3)Even if each interrupt notification is masked, in case of interrupt occurrence, interrupt elements are stored internnaly. Therefore, as soon as interrupt notification is unmasked, interrupt will generate. Interrupt notification Reference point Time from reference point to interrupt generation or interrupt generation timing RESETN release (upon power-on) 660μs INT[0] CLK stabilization completion SLEEP release (recovered from SLEEP) 660μs INT[1] INT[2] VCO calibration completion VCO calibration start 230μs INT[3] Packet discard completion during Address Filtering function SFD detection (1)If ADDFIL_NG_SET([PACKET_MODE_SET:B0 0x45(5)]) =0b0, the right timing to address mismatch detection. (2)If ADDFIL_NG_SET([PACKET_MODE_SET:B0 0x45(5)]) =0b1, (When FEC is disabled) 28byte (Length to CRC) * 8bit * 10(symbol time) + process delay(5.55μs) =2245.55μs (When FEC is enabled) 28byte (Length to CRC) * 2 * 8bit *10(symbol time) + process delay(315.55μs) =4795.55μs (TX) TX_ON command (* 1) Empty trigger level is set to 0x02 (When FEC is disabled) 37 byte (preamble to 23th data) * 8bit * 10 (symbol time) =2960μs (When FEC is enabled) {12byte (preamble to SFD) + 25byte(Length to 23th data) * 2} * 8bit* 10(symbol time) + RF wake-up & process delay (106μs) =5066μs INT[4] FIFO-Empty detection (RX) By FIFO read, remaining FIFO data is under trigger level (TX) By FIDO write, FIFO usage exceeds trigger level INT[5] FIFO-Full detection (RX) SFD detection Full trigger level is set to 0x05 (When FEC is disabled) 8byte (Length + 6 th data) * 8bit * 10(symbol time) =640μs (Wwhen FEC is enabled) 8byte (Length + 6 th data) * 8bit * 2 * 10(symbol time) + process delay(305μs) =1585μs (INT[6]) - (INT[7]) - (* 1) Befor issuing TX_ON, writing full-length TX data into a FIFO. 2 byte 2 byte 10 byte 2 byte SFD CRC Length Preamble User data |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |