| 전자부품 데이터시트 검색엔진 |
|
ATtiny43U 데이터시트(PDF) 141 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
ATtiny43U 데이터시트(HTML) 141 Page - ATMEL Corporation |
|
141 / 182 page ![]() 141 8048B–AVR–03/09 Notes: 1. See “Power Management and Sleep Modes” on page 31 for details. 2. The default value of SUT1..0 results in maximum start-up time for the default clock source. See Table 6-5 on page 26 for details. 3. The default setting of CKSEL3..0 results in internal RC Oscillator @ 8.0 MHz. See Table 6-4 on page 25 for details. Note that fuse bits are locked if Lock Bit 1 (LB1) is programmed. Fuse bits should be pro- grammed before lock bits. The status of fuse bits is not affected by chip erase. Fuse bits can also be read by device firmware. See section “Reading the Fuse and Lock Bits from Software” on page 135. 19.2.1 Latching of Fuses Fuse values are latched when the device enters programming mode and changes to fuse values have no effect until the part leaves programming mode. This does not apply to the EESAVE Fuse which will take effect once it is programmed. Fuses are also latched on power-up. 19.3 Device Signature Imprint Table The device signature imprint table is a dedicated memory area used for storing miscellaneous device information, such as the device signature and oscillator calibaration data. Most of this memory segment is reserved for internal use, as outlined in Table 19-6. Notes: 1. See section “Signature Bytes” for more information. 2. See section “Calibration Byte” for more information. Table 19-5. Fuse Low Byte Fuse Low Byte Bit No Description Default Value CKDIV8(1) 7 Divide clock by 8 0 (programmed) CKOUT 6 Clock Output Enable 1 (unprogrammed) SUT1 5 Select start-up time 1 (unprogrammed)(2) SUT0 4 Select start-up time 0 (programmed)(2) CKSEL3 3 Select Clock source 0 (programmed)(3) CKSEL2 2 Select Clock source 0 (programmed)(3) CKSEL1 1 Select Clock source 1 (unprogrammed)(3) CKSEL0 0 Select Clock source 0 (programmed)(3) Table 19-6. Contents of Device Signature Imprint Table. Address High Byte 0x00 Signature byte 0 (1) 0x01 Calibration data for internal oscillator (2) 0x02 Signature byte 1 (1) 0x03 Reserved for internal use 0x04 Signature byte 2 (1) 0x05 ... 0x2A Reserved for internal use |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |