WM8912 datasheet(80/128 Pages) WOLFSON

80 / 128 page

WM8912

Production Data

PD, Rev 4.0, September 2010

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

WSEQ_EINT_DB

Write Sequencer interrupt

debounce enable

0 = disabled

1 = enabled

GPIO1_EINT_DB

GPIO1 input debounce

0 = disabled

1 = enabled

FLL_LOCK_EINT_D

FLL Lock debounce

0 = disabled

1 = enabled

Table 54 Interrupt Control

CONTROL INTERFACE

The WM8912 is controlled by writing to registers through a 2-wire serial control interface. Readback

is available for all registers, including Chip ID, power management status and GPIO status.

Note that, if it cannot be assured that MCLK is present when accessing the register map, then it is

required to set CLK_SYS_ENA = 0 to ensure correct operation. See “Clocking and Sample Rates”

for details of CLK_SYS_ENA.

The WM8912 is a slave device on the control interface; SCLK is a clock input, while SDA is a bi-

directional data pin. To allow arbitration of multiple slaves (and/or multiple masters) on the same

interface, the WM8912 transmits logic 1 by tri-stating the SDA pin, rather than pulling it high. An

external pull-up resistor is required to pull the SDA line high so that the logic 1 can be recognised by

the master.

In order to allow many devices to share a single 2-wire control bus, every device on the bus has a

unique 8-bit device ID (this is not the same as the 8-bit address of each register in the WM8912).

The WM8912 device ID is 0011 0100 (34h). The LSB of the device ID is the Read/Write bit; this bit is

set to logic 1 for “Read” and logic 0 for “Write”.

The WM8912 operates as a slave device only. The controller indicates the start of data transfer with

a high to low transition on SDA while SCLK remains high. This indicates that a device ID, register

address and data will follow. The WM8912 responds to the start condition and shifts in the next eight

bits on SDA (8-bit device ID including Read/Write bit, MSB first). If the device ID received matches

the device ID of the WM8912, then the WM8912 responds by pulling SDA low on the next clock

pulse (ACK). If the device ID is not recognised or the R/W bit is ‘1’ when operating in write only

mode, the WM8912 returns to the idle condition and waits for a new start condition and valid

address.

If the device ID matches the device ID of the WM8912, the data transfer continues as described

below. The controller indicates the end of data transfer with a low to high transition on SDA while

SCLK remains high. After receiving a complete address and data sequence the WM8912 returns to

the idle state and waits for another start condition. If a start or stop condition is detected out of

sequence at any point during data transfer (i.e. SDA changes while SCLK is high), the device returns

to the idle condition.

The WM8912 supports the following read and write operations:

•

Single write

•

Single read

•

Multiple write using auto-increment

•

Multiple read using auto-increment

WM8912 데이터시트(PDF) 80 Page - Wolfson Microelectronics plc

WM8912 데이터시트(HTML) 80 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL