HCS08 datasheet(97/316 Pages) NXP

97 / 316 page

Chapter 7 Central Processor Unit (S08CPUV2)

MC9S08SG8 MCU Series Data Sheet, Rev. 8

Freescale Semiconductor

7.4.1

Reset Sequence

Reset can be caused by a power-on-reset (POR) event, internal conditions such as the COP (computer

operating properly) watchdog, or by assertion of an external active-low reset pin. When a reset event

occurs, the CPU immediately stops whatever it is doing (the MCU does not wait for an instruction

boundary before responding to a reset event). For a more detailed discussion about how the MCU

recognizes resets and determines the source, refer to the Resets, Interrupts, and System Configuration

chapter.

The reset event is considered concluded when the sequence to determine whether the reset came from an

internal source is done and when the reset pin is no longer asserted. At the conclusion of a reset event, the

CPU performs a 6-cycle sequence to fetch the reset vector from 0xFFFE and 0xFFFF and to fill the

instruction queue in preparation for execution of the first program instruction.

7.4.2

Interrupt Sequence

When an interrupt is requested, the CPU completes the current instruction before responding to the

interrupt. At this point, the program counter is pointing at the start of the next instruction, which is where

the CPU should return after servicing the interrupt. The CPU responds to an interrupt by performing the

same sequence of operations as for a software interrupt (SWI) instruction, except the address used for the

vector fetch is determined by the highest priority interrupt that is pending when the interrupt sequence

started.

The CPU sequence for an interrupt is:

1. Store the contents of PCL, PCH, X, A, and CCR on the stack, in that order.

2. Set the I bit in the CCR.

3. Fetch the high-order half of the interrupt vector.

4. Fetch the low-order half of the interrupt vector.

5. Delay for one free bus cycle.

6. Fetch three bytes of program information starting at the address indicated by the interrupt vector

to fill the instruction queue in preparation for execution of the first instruction in the interrupt

service routine.

After the CCR contents are pushed onto the stack, the I bit in the CCR is set to prevent other interrupts

while in the interrupt service routine. Although it is possible to clear the I bit with an instruction in the

interrupt service routine, this would allow nesting of interrupts (which is not recommended because it

leads to programs that are difficult to debug and maintain).

For compatibility with the earlier M68HC05 MCUs, the high-order half of the H:X index register pair (H)

is not saved on the stack as part of the interrupt sequence. The user must use a PSHH instruction at the

beginning of the service routine to save H and then use a PULH instruction just before the RTI that ends

the interrupt service routine. It is not necessary to save H if you are certain that the interrupt service routine

does not use any instructions or auto-increment addressing modes that might change the value of H.

The software interrupt (SWI) instruction is like a hardware interrupt except that it is not masked by the

global I bit in the CCR and it is associated with an instruction opcode within the program so it is not

asynchronous to program execution.

HCS08 데이터시트(PDF) 97 Page - NXP Semiconductors

HCS08 데이터시트(HTML) 97 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL