| 전자부품 데이터시트 검색엔진 |
|
AFE4490 데이터시트(PDF) 32 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
AFE4490 데이터시트(HTML) 32 Page - Texas Instruments |
|
32 / 85 page ![]() ADC_RDY Register 2Eh Register 3Fh ADC Conversion of (LED2-Ambient2) Data 5 Data 6 Data 7 Data 8 Data 9 Data 10 Data 11 Data 12 Data 4 Average of Data 5, 6, 7, 8 Average of Data 1, 2, 3, 4 25-Hz Frequency PRF Setting, 100 Hz LED On Data 5 Data 6 Data 7 Data 8 Data 9 Data 10 Data 11 Data 12 Data 4 32 AFE4404 SBAS689D – JUNE 2015 – REVISED DECEMBER 2016 www.ti.com Product Folder Links: AFE4404 Submit Documentation Feedback Copyright © 2015–2016, Texas Instruments Incorporated 8.4.6 Decimation Mode The AFE4404 has a decimation mode that can be used to improve the performance at low pulse repetition frequencies (PRFs). In this mode, up to N (N = 2, 4, 8, or 16) consecutive data samples can be averaged. The averaged output comes out one time every N clock cycles. The ADC_RDY frequency also reduces to PRF / N. A timing diagram is shown in Figure 37 for where the decimation factor = 4 and PRF = 100 Hz. Figure 37 is only intended to illustrate the change in periodicity of ADC_RDY and the update rate of the registers relative to the pulse repetition period. However, the timing of all other signals continues to be as per the descriptions mentioned in the Timing Engine section. Figure 37. Decimation Mode Enabled Timing Diagram (Decimation Factor = 4, PRF = 100 Hz) 8.4.6.1 Decimation Mode Power and Performance The main advantage of the decimation mode is that this mode can be used to reduce the readout rate of the MCU because the data rate reduces by the decimation factor. Normally, reducing the data rate leads to SNR loss. However, with decimation mode, there is no SNR loss regardless of the lower data rate because of the averaging of consecutive samples. Table 15 compares different modes of operation. Table 15. Different Modes of Operation MODE RATE OF DEVICE SAMPLES AND CONVERSIONS RATE OF MCU DATA READS RELATIVE PERFORMANCE No decimation, 100-Hz PRF 100 Hz 100 Hz Reference No decimation, 25-Hz PRF 25 Hz 25 Hz SNR is approximately 6 dB lower than reference 4X decimation mode, 100-Hz PRF 100 Hz 25 Hz SNR is comparable to reference |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |