| 전자부품 데이터시트 검색엔진 |
|
LPC1547JBD48 데이터시트(PDF) 31 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC1547JBD48 데이터시트(HTML) 31 Page - NXP Semiconductors |
|
31 / 99 page ![]() LPC15XX All information provided in this document is subject to legal disclaimers. © NXP B.V. 2014. All rights reserved. Product data sheet Rev. 1 — 19 February 2014 31 of 99 NXP Semiconductors LPC15xx 32-bit ARM Cortex-M3 microcontroller 8.18 USART0/1/2 Remark: All USART functions are movable functions and are assigned to pins through the switch matrix. Do not connect USART functions to the open-drain pins PIO0_22 and PIO0_23. Interrupts generated by the USART peripherals can wake up the part from Deep-sleep and power-down modes if the USART is in synchronous mode, the 32 kHz mode is enabled, or the CTS interrupt is enabled. 8.18.1 Features • Maximum bit rates of 4.5 Mbit/s in asynchronous mode, 15 Mbit/s in synchronous mode master mode, and 18 Mbit/s in synchronous slave mode. • 7, 8, or 9 data bits and 1 or 2 stop bits. • Synchronous mode with master or slave operation. Includes data phase selection and continuous clock option. • Multiprocessor/multidrop (9-bit) mode with software address compare. • RS-485 transceiver output enable. • Autobaud mode for automatic baud rate detection • Parity generation and checking: odd, even, or none. • Software selectable oversampling from 5 to 16 clocks in asynchronous mode. • One transmit and one receive data buffer. • RTS/CTS for hardware signaling for automatic flow control. Software flow control can be performed using Delta CTS detect, Transmit Disable control, and any GPIO as an RTS output. • Received data and status can optionally be read from a single register • Break generation and detection. • Receive data is 2 of 3 sample "voting". Status flag set when one sample differs. • Built-in Baud Rate Generator with auto-baud function. • A fractional rate divider is shared among all USARTs. • Interrupts available for Receiver Ready, Transmitter Ready, Receiver Idle, change in receiver break detect, Framing error, Parity error, Overrun, Underrun, Delta CTS detect, and receiver sample noise detected. • Loopback mode for testing of data and flow control. • In synchronous slave mode, wakes up the part from deep-sleep and power-down modes. • Special operating mode allows operation at up to 9600 baud using the 32 kHz RTC oscillator as the UART clock. This mode can be used while the device is in Deep-sleep or Power-down mode and can wake-up the device when a character is received. • USART transmit and receive functions work with the system DMA controller. 8.19 SPI0/1 All SPI functions are movable functions and are assigned to pins through the switch matrix. Do not connect SPI functions to the open-drain pins PIO0_22 and PIO0_23. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |