MT9072AB datasheet(192/275 Pages) ZARLINK

192 / 275 page

MT9072

Data Sheet

192

Zarlink Semiconductor Inc.

17.2.5

Latched Status Registers (Y2X) Bit Functions

Tables 173 to 181 describe the bit functions of each of the Latched Status Registers in the MT9072 in E1 mode.

Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2

with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB)

A11-A8). All latched status registers will be reset in the inactive state upon reset.

Bit

Name

Functional Description

15-9

#######

not used.

8GAL

Go Ahead received Latch.Indicates a go-ahead pattern (01111111) was detected by the

HDLC receiver. This bit is reset after a read.

7EOPDL

End of Packet Data Latch.This bit is set when an end of packet (EOP) byte was written

into the RX FIFO by the HDLC receiver. This can be in the form of a flag, an abort

sequence or as an invalid packet. This bit is reset after a read.

TEOPL

Transmit End of Packet Latch.This bit is set when the transmitter has finished sending

the closing flag of a packet or after a packet has been aborted. This bit is reset after read.

5EOPRL

End of Packet received latch.This bit is set when the byte about to be read from the RX

FIFO is the last byte of the packet. It is also set if the Rx FIFO is read and there is no data

in it. This bit is reset after a read.

4TXFL

Transmit Fifo Low Latch.This bit is set when the Tx FIFO is emptied below the selected

low threshold level. This bit is reset after a read.

3FAL

Framer Abort Latch. This bit (FA) is set when a frame abort is received during packet

reception. It must be received after a minimum number of bits have been received (26)

otherwise it is ignored.

TXunder

Txunder Latch.This bit is set for a TX FIFO underrun indication. If high it Indicates that a

read by the transmitter was attempted on an empty Tx FIFO. This bit is reset after a read.

1RxffL

Receive Fifo Full Latch.This bit is set when the Rx FIFO is filled above the selected full

threshold level. This bit is reset after a read.

0RxOvfL

Receive Overflow Latch.Indicates that the 32 byte RX FIFO overflowed (i.e., an attempt

to write to a 32 byte full RX FIFO). The HDLC will always disable the receiver once the

receive overflow has been detected. The receiver will be re-enabled upon detection of the

next flag, but will overflow again unless the RX FIFO is read. This bit is reset after a read.

Table 168 - HDLC Status Latch(Y23) (E1)

Bit

Name

Functional Description

not used.

RCRCRL Remote CRC-4 and RAI Latch. When the RCRCR status bit (register address Y10) toggles

from zero to one, this status bit is latched to one. This bit is cleared when either this register,

or the interrupt status register (register address Y34) is read.

RSLPL

Receive Slip Latch. When the RSLP status bit (register address Y13) toggles from zero to

one, or from one to zero, this status bit is latched to one. This bit is cleared when either this

Table 169 - Sync, CRC-4 Remote, Alarms, MAS and Phase Latched Status Register (Address Y24) (E1)

MT9072AB 데이터시트(PDF) 192 Page - Zarlink Semiconductor Inc

MT9072AB 데이터시트(HTML) 192 Page - Zarlink Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL