| 전자부품 데이터시트 검색엔진 |
|
P5021 데이터시트(PDF) 58 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
P5021 데이터시트(HTML) 58 Page - NXP Semiconductors |
|
58 / 155 page ![]() P5021 QorIQ Integrated Processor Data Sheet, Rev. 1 Electrical characteristics Freescale Semiconductor 58 2.1.3 Output driver characteristics This table provides information about the characteristics of the output driver strengths. The values are preliminary estimates. 2.2 Power-up sequencing The chip requires that its power rails be applied in a specific sequence in order to ensure proper device operation. These requirements are as follows for power up: 1. Bring up OVDD, LVDD, BVDD, CVDD, and USB_VDD_3P3. Drive POVDD = GND. — PORESET input must be driven asserted and held during this step — IO_VSEL inputs must be driven during this step and held stable during normal operation. —USB_VDD_3P3 rise time (10% to 90%) has a minimum of 350 μs. 2. Bring up VDD_PL, VDD_CA, SVDD, AVDD (cores, platform, DDR, SerDes) and USB_VDD_1P0. VDD_PL and USB_VDD_1P0 must be ramped up simultaneously. 3. Bring up GVDD and XVDD. 4. Negate PORESET input as long as the required assertion/hold time has been met per Table 15. 5. For secure boot fuse programming: After negation of PORESET, drive POVDD = 1.5 V after a required minimum delay per Table 5. After fuse programming is completed, it is required to return POVDD = GND before the system is power cycled (PORESET assertion) or powered down (VDD_PL ramp down) per the required timing specified in Table 5. See Section 5, “Security fuse processor,” for additional details. WARNING Only two secure boot fuse programming events are permitted per lifetime of a device. No activity other than that required for secure boot fuse programming is permitted while POVDD driven to any voltage above GND, including the reading of the fuse block. The reading of the fuse block may only occur while POVDD = GND. Table 4. Output drive capability Driver type Output impedance ( Ω) (Nominal) supply voltage Notes Local bus interface utilities signals 45 45 45 BVDD = 3.3 V BVDD = 2.5 V BVDD = 1.8 V — DDR3 signal 20 (full-strength mode) 40 (half-strength mode) GVDD = 1.5 V 1 DDR3L signal 20 (full-strength mode) 40 (half-strength mode) GVDD = 1.35 V 1 eTSEC/10/100 signals 45 45 LVDD = 3.3 V LVDD = 2.5 V — DUART, system control, JTAG 45 OVDD = 3.3 V — I2C45 OVDD = 3.3 V — eSPI and SD/MMC 45 45 45 CVDD = 3.3 V CVDD = 2.5 V CVDD = 1.8 V — Note: 1. The drive strength of the DDR3 or DDR3L interface in half-strength mode is at Tj = 105 °C and at GVDD (min). |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |