| 전자부품 데이터시트 검색엔진 |
|
MPC8308CVMADDA 데이터시트(PDF) 42 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
MPC8308CVMADDA 데이터시트(HTML) 42 Page - NXP Semiconductors |
|
42 / 95 page ![]() MPC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 4 42 Freescale Semiconductor Enhanced Local Bus 12.1 Enhanced Local Bus DC Electrical Characteristics This table provides the DC electrical characteristics for the local bus interface. 12.2 Enhanced Local Bus AC Electrical Specifications This table describes the general timing parameters of the local bus interface. This figure provides the AC test load for the local bus. Figure 30. Local Bus AC Test Load Table 36. Local Bus DC Electrical Characteristics at 3.3 V Parameter Symbol Min Max Unit High-level input voltage VIH 2.0 NVDD + 0.3 V Low-level input voltage VIL –0.3 0.8 V Input current, (VIN 1 = 0 V or V IN = LVDD)IIN — ±5 A High-level output voltage, (LVDD = min, IOH = –2 mA) VOH NVDD – 0.2 — V Low-level output voltage, (LVDD = min, IOL = 2 mA) VOL —0.2 V Note: The parameters stated in above table are valid for all revisions unless explicitly mentioned. Table 37. Local Bus General Timing Parameters Parameter Symbol 1 Min Max Unit Notes Local bus cycle time tLBK 15 — ns 2 Input setup to local bus clock tLBIVKH 7 — ns 3, 4 Input hold from local bus clock tLBIXKH 1 — ns 3, 4 Local bus clock to output valid tLBKHOV —3 ns 3 Local bus clock to output high impedance for LD tLBKHOZ —4 ns 5 Notes: 1. The symbols used for timing specifications follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). 2. All timings are in reference to falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or rising edge of LCLK0 (for all other inputs). 3. All signals are measured from NVDD/2 of the rising/falling edge of LCLK0 to 0.4 NVDD of the signal in question for 3.3-V signaling levels. 4. Input timings are measured at the pin. 5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. Output Z0 = 50 NVDD/2 RL = 50 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |