| 전자부품 데이터시트 검색엔진 |
|
AN3077 데이터시트(PDF) 17 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
AN3077 데이터시트(HTML) 17 Page - STMicroelectronics |
|
17 / 82 page ![]() DocID16384 Rev 10 17/82 AN3077 Functional safety requirements for application software 81 Note: Implementation hint: A possible way to detect spurious interrupts is to check corresponding interrupt status in the interrupt status register of the related peripheral before executing the Interrupt Service Routine (ISR) service code. 3.9 Semaphore Unit (SEMA4) Semaphore modules are only used in DPM. Failures of the SEMA4 module may cause unwanted interrupts in LSM. Each SEMA4 unit is connected to both replicated INTC modules. This means that even in LSM when SEMA4 units are not used, a corrupted SEMA4 could trigger continuous interrupts to both INTCs. To avoid this possible failure the INTC shall have the SEMA4 interrupt masked (for example, SEMA4 units have the lowest priority in the INTCs). Mandatory: Application software shall keep these interrupt sources masked by programming the interrupt controller appropriately. 3.10 Enhanced Direct Memory Access (eDMA) requests Mandatory: For ASIL D applications, protection against spurious or missing safety relevant eDMA requests must be implemented(d). The methodology used to satisfy this requirement is application dependent. Note: Rationale: To manage spurious or missing eDMA transfer requests Note: Implementation hint: Some implementations which can satisfy these requirements are: ● Counting the number of eDMA transfers triggered inside a control period and compare this with what is the expected value. ● If the eDMA is used to manage the analog acquisition with the Cross-Triggering Unit (CTU) and ADC, the number of the converted ADC channels is saved in the CTU FIFO together with the acquired value. The eDMA transfers this value from the CTU FIFO to a respective SRAM location. Spurious or missing transfer requests can be detected by comparing the converted channel with what is expected. Mandatory: Designers must not use the Periodic Interrupt Timer (PIT) module to trigger an eDMA transfer request for ASIL D applications. Note: Rationale: To avoid a faulty PIT (which is not redundant) from triggering an unexpected eDMA transfer 3.11 Periodic Interrupt Timer (PIT) Mandatory: For ASIL D applications the PIT module must be used in such a way that a possible failure is detected by the Software Watchdog Timer (SWT). Note: Rationale: To catch possible PIT failures Mandatory: If the PIT is used by ASIL D applications, a checksum of its configuration registers must be calculated and compared with the expected value to verify that the PIT d. eDMA is a replicated module. No software action is needed to detect faults inside this module. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |