LAN9730 datasheet(72/222 Pages) MICROCHIP

72 / 222 page

LAN9730/LAN9730i

DS00001946A-page 72

 2012-2015 Microchip Technology Inc.

4.5.7.1

RX Checksum Calculation

The checksum is calculated 16 bits at a time. In the case of an odd sized frame, an extra byte of zero is used to pad up

to 16 bits.

Consider the following packet: DA, SA, Type, B0, B1, B2 … BN, FCS

Let [A, B] = A*256 + B

If the packet has an even number of octets then

checksum = [B1, B0] + C0 + [B3, B2] + C1 + … + [BN, BN-1] + CN-1

Where C0, C1, ... CN-1 are the carry out results of the intermediate sums.

If the packet has an odd number of octets then

checksum = [B1, B0] + C0 + [B3, B2] + C1 + … + [0, BN] + CN-1

4.5.8

TRANSMIT CHECKSUM OFFLOAD ENGINE (TXCOE)

The transmit checksum offload engine provides assistance to the CPU by calculating a 16-bit checksum, typically for

TCP, for a transmit Ethernet frame. The TXCOE calculates the checksum and inserts the results back into the data

stream as it is transferred to the MAC.

To activate the TXCOE and perform a checksum calculation, the host must first set the TX Checksum Offload Engine

Enable (TX_COE_EN) bit in the Checksum Offload Engine Control Register (COE_CR). The host then pre-pends a 3

DWORD buffer to the data that will be transmitted. The pre-pended buffer includes a TX Command A, TX Command B,

and a 32-bit TX checksum preamble (refer to Table 4-53). When the CK bit of the TX Command ‘B’ is set in conjunction

with the FS bit of TX Command ‘A’ and the TX_COE_EN bit of the COE_CR register, the TXCOE will perform a check-

sum calculation on the associated packet. The TX checksum preamble instructs the TXCOE on the handling of the asso-

ciated packet. The TXCSSP - TX Checksum Start Pointer field of the TX checksum preamble defines the byte offset at

which the data checksum calculation will begin. The checksum calculation will begin at this offset and will continue until

the end of the packet. The data checksum calculation must not begin in the MAC header (first 14 bytes) or in the last 4

bytes of the TX packet. When the calculation is complete, the checksum will be inserted into the packet at the byte offset

defined by the TXCSLOC - TX Checksum Location field of the TX checksum preamble. The TX checksum cannot be

inserted in the MAC header (first 14 bytes) or in the last 4 bytes of the TX packet. If the CK bit is not set in the first TX

Command ‘B’ of a packet, the packet is passed directly through the TXCOE without modification, regardless if the

TXCOE_EN is set. An example of a TX packet with a pre-pended TX checksum preamble can be found in Section

4.4.2.9, "TX Example 3". In this example, the host provides the Ethernet frame to the Ethernet controller (via a USB

packet) in four fragments, the first containing the TX Checksum Preamble. Figure 4-8 shows how these fragments are

loaded into the TX Data FIFO. For more information on the TX Command ‘A’ and TX Command ‘B’, refer to Section

4.4.2.1, "TX Command Format".

If the TX packet already includes a partial checksum calculation (perhaps inserted by an upper layer protocol), this

checksum can be included in the hardware checksum calculation by setting the TXCSSP field in the TX checksum pre-

amble to include the partial checksum. The partial checksum can be replaced by the completed checksum calculation

by setting the TXCSLOC pointer to point to the location of the partial checksum.

LAN9730 데이터시트(PDF) 72 Page - Microchip Technology