MT9072AB datasheet(174/275 Pages) ZARLINK

174 / 275 page

MT9072

Data Sheet

174

Zarlink Semiconductor Inc.

8PLBK

(0)

Payload Loopback. If one, all timeslots received on RPOS/RNEG are connected to

TPOS/TNEG on the ST-BUS side(DSTo to DSTi) of the selected framer (Y) (this excludes

time-slot 0). Hence the data passes through the receiver and output to DSTo. This DSTo data

is looped back to DSTi which is transmitted to TPOS/TNEG by the transmitter.

If zero, this feature is disabled. See Loopbacks section.

7E1

(0)

E1 Error Insertion. A zero-to-one transition of this bit inserts a single E1 error into the

transmit PCM30 data (bit position 1 of frame 13 of the CRC-4 Multiframe). A one, zero or

one-to-zero transition has no function.

6E2

(0)

E2 Error Insertion. A zero-to-one transition of this bit inserts a single E2 error into the

transmit PCM30 data (bit position 1 of frame 15 of the CRC-4 Multiframe). A one, zero or

one-to-zero transition has no function.

BVE

(0)

Bipolar Violation Error Insertion. A zero-to-one transition of this bit inserts a single bipolar

violation error into the transmit PCM30 data. A one, zero or one-to-zero transition has no

function.

CRCE

(0)

CRC-4 Error Insertion. A zero-to-one transition of this bit inserts a single CRC-4 error into

the transmit PCM30 data. A one, zero or one-to-zero transition has no function.

FASE

(0)

Frame Alignment Signal Error Insertion. A zero-to-one transition of this bit inserts a single

error into the timeslot zero frame alignment signal of the transmit PCM30 data. A one, zero or

one-to-zero transition has no function.

2NFSE

(0)

Non-frame Alignment Signal Error Insertion. A zero-to-one transition of this bit inserts a

single error into bit two of the timeslot zero non-frame alignment signal of the transmit PCM30

data. A one, zero or one-to-zero transition has no function.

1LOSE

(0)

Loss of Signal Error Insertion. If one, the selected framer (Y) transmits an all zeros signal

(no pulses) in every PCM30 timeslot, and, the HDB3 control bit (reg address Y02) has no

effect. If zero, data is transmitted normally.

PERR

(0)

Payload Error Insertion. A zero-to-one transition of this bit inserts a single error in the

transmit payload. A one, zero or one-to-zero transition has no function.

Bit

Name

Functional Description

COD1

COD0

(1 0)

Line Coding. These two coding select bits determine the transmit and receive coding options as

follows. See Figures 64 to 67.

COD1 COD0 Function

RZ (Return to Zero, Dual Rail)

NRZ (Non-return to Zero, Single Rail)

NRZB (Non-return to Zero, Dual Rail)

No function

13 RHDB3

(0)

RHDB3 (High Density Bipolar 3) encoding. If zero, HDB3 decoding is enabled in the receive

direction. If one, AMI (Alternate Mark Inversion) signal without HDB3 decoding is enabled in the

transmit direction.

Table 144 - Interrupts and I/O Control Register (R/W Address Y02) (E1)

Bit

Name

Functional Description

Table 143 - Test, Error and Loopback Control Register (R/W Address Y01) (E1)

MT9072AB 데이터시트(PDF) 174 Page - Zarlink Semiconductor Inc

MT9072AB 데이터시트(HTML) 174 Page - Zarlink Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL