PC87373 datasheet(90/174 Pages) NSC

90 / 174 page

6.0 System Wake-Up Control (SWC) (Continued)

www.national.com

Revision 1.1

6.3.3

SWC Miscellaneous Control Register (SWC_CTL)

This register contains control and status bits for the SWC module. Its reset value depends on the power well of each bit.

Power Well: VSB3

Location:

Offset 01h

Type:

Varies per bit

Bit

43210

Name

LOCKSCF

Reserved

GOOD_

BAT

Reserved

LAST_PWR

_STATE

LED_OPT

Reset

‘01’ or ‘10’

Power Well

VSB3

VBAT

VSB3

Bit

Type

Description

R/W1S LOCKSCF (Lock SWC Configuration). When set to 1, this bit locks the BLINK and GRN_YLW bits in

SLEDCTL register, and all bits of SWC_CTL, ALEDCTL, LEDBLNK, XLEDCTL, KBDWKCTL, PS2CTL

and PS2KEY0

−7 registers by disabling writing to them (including to the LOCKSCF bit itself). Once set,

this bit can be cleared by VDD3 Power-Up reset (or Hardware reset).

0: R/W bits are enabled for write (default)

1: All bits are RO

Reserved.

5RO

GOOD_BAT (Battery Good Status). This bit indicates the status of the VBAT backup power. The bit is

Reset at any time, if VBAT <VBATLOW

Set when either VDD3 or VSB3 power supply falls below the minimum limit, if VBAT >VBATLOW

When the bit is ‘0’, the value of the LAST_PWR_STATE bit is incorrect and must be ignored.

0: Backup battery low, or not connected (VBAT <VBATLOW)

1: Backup battery good (VBAT > VBATLOW)

4-3

Reserved.

2RO

LAST_PWR_STATE (Last Power State). This bit samples the value of the SLP_S3 signal when a

power failure occurs. It is powered by the VBAT backup supply, thus preserving its value during a Power

Fail condition (see Section 2.1.2 on page 27). After the AC power returns, reading from this bit returns

the value of the SLP_S3 signal at the time the power failure occurred. The value of this bit must be

ignored when GOOD_BAT bit is 0. Writing to this bit is ignored. At VBAT Power-Up reset,

LAST_PWR_STATE bit is reset to 0.

0: Orderly system shutdown - Main power off by S3 or S5 sleep states (default)

1: Forced system shutdown - Main power off by Mechanical off (G2 state) or by AC power failure

1-0

R/W or

LED_OPT (LED Control Option Select). Selects the Advanced, Standard or Special LED control

option for the two power LEDs (yellow and green).

Bits

1 0

LED Control Option

0 0:

Advanced: LEDs controlled by the ALEDCTL and LEDBLNK registers at offsets 02h and 03h,

respectively

0 1:

Standard: LEDs controlled by SLEDCTL register at offset 00h

(default if VBAT < VBATLOW at VSB3 Power-Up reset)

1 0:

Special:

LEDs controlled by XLEDCTL register at offset 02h

(default if VBAT > VPPLOW at VSB3 Power-Up reset)

1 1:

Reserved

PC87373 데이터시트(PDF) 90 Page - National Semiconductor (TI)

PC87373 데이터시트(HTML) 90 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL