STM8S datasheet(298/467 Pages) STMICROELECTRONICS

298 / 467 page

Inter-integrated circuit (I2C) interface

RM0016

298/467

DocID14587 Rev 14

EV5: SB=1, cleared by reading SR1 register followed by writing DR register.

EV6: ADDR=1, cleared by reading SR1 register followed by reading SR3. In 10-bit master receiver mode,

this sequence should be followed by writing CR2 with START = 1.

EV6_1: no associated flag event, used for 1 byte reception only. Program ACK=0 and STOP=1 after

clearing ADDR.

EV7: RxNE=1, cleared by reading DR register.

EV7_1: RxNE=1, cleared by reading DR register, program ACK=0 and STOP request

EV9: ADD10=1, cleared by reading SR1 register followed by writing DR register.

2. If the DR and shift registers are full, the next data reception (I2C clock generation for slave) is performed

after the EV7 event is cleared. In this case, EV7 does not overlap with data reception.

3. If a single byte is received, it is NA.

4. EV5, EV6 and EV9 events stretch SCL low until the end of the corresponding software sequence.

5. EV7 software sequence must be completed before the end of the current byte transfer.In case EV7

software sequence can not be managed before the current byte end of transfer, it is recommended to use

BTF instead of RXNE with the drawback of slowing the communication.

6. The EV6_1 or EV7_1 software sequence must be completed before the ACK pulse of the current byte

transfer.

7. See also: Note 8 on page 311.

Method 2: This method is for the case when the I2C is used with interrupts that do not have

the highest priority in the application or when the I2C is used with polling.

With this method:

•

DataN_2 is not read, so that after DataN_1, the communication is stretched (both

RxNE and BTF are set).

•

Then, the ACK bit must be cleared before reading DataN-2 in DR to make sure this bit

has been cleared before the DataN Acknowledge pulse.

•

After that, just after reading DataN_2, software must set the STOP/ START bit and read

DataN_1. After RxNE is set, read DataN.

This is illustrated in the following figure:

Figure 106. Method 2: transfer sequence diagram for master receiver when N >2

1. Legend:

S= Start, Sr = Repeated Start, P= Stop, A= Acknowledge, NA= Non-acknowledge,

EVx= Event (with interrupt if ITEVTEN=1)

EV5: SB=1, cleared by reading SR1 register followed by writing the DR register.

EV6: ADDR1, cleared by reading SR1 register followed by reading SR3.

In 10-bit master receiver mode, this sequence should be followed by writing CR2 with START = 1.

EV7: RxNE=1, cleared by reading DR register.

EV7_2: BTF = 1, DataN-2 in DR and DataN-1 in shift register, program ACK = 0, Read DataN-2 in DR.

Program STOP = 1, read DataN-1.

MSv47721V1

EV7_2

EV5

Address

EV6

Data1

Data2

EV7

DataN-2

(1)

...

DataN-1

DataN

NA P

EV7

EV5

Header

EV9

Address

EV6

EV7_2

EV5

Header

EV6

Data1

Data2

EV7

DataN-2

DataN-1

DataN

EV7

...

7-bit master receiver

10-bit master receiver

STM8S 데이터시트(PDF) 298 Page - STMicroelectronics

STM8S 데이터시트(HTML) 298 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL