| 전자부품 데이터시트 검색엔진 |
|
AR8327-AL1A-R 데이터시트(PDF) 37 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
AR8327-AL1A-R 데이터시트(HTML) 37 Page - List of Unclassifed Manufacturers |
|
37 / 394 page ![]() Atheros Communications, Inc. AR8327/AR8327N Seven-port Gigabit Ethernet Switch • 37 2.9 LED Control There are totally 6 Led control rules. Three of them are used to control the LEDs of PHY 0 to PHY 3. The others are used to control the LEDs of PHY4. Each port has 3 LEDs, the default behavior of the LEDs are 1000_link_activity, 100_link_activity and 10_link_activity. The LED output is open-drain output type. So two or three of them can be connected together to indicate OR operation of the original LEDs. To achieve this operation, another way is to modify the LED control register. These LEDs also can be individually configured on or off by register. Each LED can be controlled by 16-bits shown in the following table. Table 2-21. LED Control Bit Name Description 15:14 PATTERN_EN 2’b00: LED always off 2’b01: LED blinking at 4 Hz 2’b10: LED always on 2’b11: LED controlled by the following bits 13 FULL_LIGHT_EN 1’b1: LED will light when link up in full-duplex 12 HALF_LIGHT_EN 1’b1: LED will light when link up at half-duplex 11 POWER_ON_LIGHT_EN 1’b1: module should enter POWER_ON_RESET status after reset. 10 LINK_1000M_LIGHT_EN 1’b1: LED will light when link up at 1000 Mbps 9 LINK_100M_LIGHT_EN 1’b1: LED will light when link up at 100 Mbps 8 LINK_10M_LIGHT_EN 1’b1: LED will light when link up at 10 Mbps 7 COL_BLINK_EN 1’b1: LED will blink when collision is detected 6 Reserved Must be 1’b0 5 RX_BLINK_EN 1’b1: LED will blink when receiving frame 4 TX_BLINK_EN 1’b1: LED will blink when transmitting frame 3 Reserved Must be 1’b0 2 LINKUP_OVER_EN 1’b1: RX/TX blinking should check with LINKUP speed, LINKUP LED is ON, allow blinking. Otherwise, OFF 1’b0: RX/TX blinking will ignore the LINKUP speed. 1:0 LED_BLINK_FREQ LED blink frequency select 2’b00: 2 HZ 2’b01: 4 Hz 2’b10: 8 Hz 2’b11: if link up at 1000Mbps, 8 Hz if link up at 100Mbps, use 4 Hz if link up at 10 Mbps, use 2 Hz Table 2-22. LED Rule Default Value Bit Name LED_RULE_0/1 LED_RULE_2/3 LED_RULE_4/5 Default Value 0xCC35 0xCA35 0xC935 15:14 PATTERN_EN 2’b11 2’b11 2’b11 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |