| 전자부품 데이터시트 검색엔진 |
|
DS2408S/T 데이터시트(PDF) 8 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
DS2408S/T 데이터시트(HTML) 8 Page - Maxim Integrated Products |
|
8 / 36 page ![]() DS2408 Figure 5. DS2408 REGISTER ADDRESS MAP ADDRESS RANGE ACCESS TYPE DESCRIPTION 0000h to 0087h R Undefined Data 0088h R PIO Logic State 0089h R PIO Output Latch State Register 008Ah R PIO Activity Latch State Register 008Bh R/W Conditional Search Channel Selection Mask 008Ch R/W Conditional Search Channel Polarity Selection 008Dh R/W Control/Status Register 008Eh to 008Fh R These Bytes Always Read FFh PIO Logic-State Register The logic state of the PIO pins can be obtained by reading this register using the Read PIO Registers command. Reading this register does not generate a signal at the RSTZ pin, even if it is configured as STRB . See the Channel-Access commands description for details on STRB . PIO Logic State Register Bitmap ADDR b7 b6 b5 b4 b3 b2 b1 b0 0088h P7 P6 P5 P4 P3 P2 P1 P0 This register is read-only. Each bit is associated with the pin of the respective PIO channel as shown in Figure 6. The data in this register is sampled at the last (most significant) bit of the byte that proceeds reading the first (least significant) bit of this register. See the Read PIO Registers command description for details. PIO Output Latch State Register The data in this register represents the latest data written to the PIO through the Channel-access Write command. This register is read using the Read PIO Registers command. Reading this register does not generate a signal at the RSTZ pin, even if it is configured as STRB . See the Channel-access commands description for details on STRB . This register is not affected if the device reinitializes itself after an ESD hit. PIO Output Latch State Register Bitmap ADDR b7 b6 b5 b4 b3 b2 b1 b0 0089h PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 This register is read-only. Each bit is associated with the output latch of the respective PIO channel as shown in Figure 6. The flip-flops of this register will power up in a random state. If the chip has to power up with all PIO channels off, a LOW pulse must be generated on the RSTZ pin, e.g., by means of an open-drain CPU supervisor chip (see Figure 20). When using an RC circuit to generate the power-on reset, make sure that RSTZ is NOT configured as strobe output (ROS bit in control/status register 008Dh needs to be 0). 8 of 36 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |