| 전자부품 데이터시트 검색엔진 |
|
DS2408S/T 데이터시트(PDF) 5 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
DS2408S/T 데이터시트(HTML) 5 Page - Maxim Integrated Products |
|
5 / 36 page ![]() DS2408 PIN DESCRIPTION PIN NAME DESCRIPTION 1 N.C. Not Connected 2 P0 I/O Pin of Channel 0. Logic input/open-drain output with 100 W maximum on-resistance; 0V to 5.25V operating range. Power-on default is indeterminate. If it is application-critical for the outputs to power up in the "off" state, the user should attach an appropriate power-on-reset circuit or supervisor IC to the RSTZ pin. 3 VCC Optional Power Supply Input. Range 2.8V to 5.25V; must be tied to GND if not used. 4 I/O 1-Wire Interface. Open-drain, requires external pullup resistor. 5 GND Ground 6 N.C. Not Connected 7 P7 I/O Pin of Channel 7. Same characteristics as P0. 8 P6 I/O Pin of Channel 6. Same characteristics as P0. 9 P5 I/O Pin of Channel 5. Same characteristics as P0. 10 RSTZ SW configurable PIO reset input ( RST ) or open-drain strobe output (STRB ). When configured as RST , a LOW input sets all PIO outputs to the "off" state by setting all bits in the PIO Output Latch State Register. When configured as STRB , an output strobe will occur after a PIO write (see Channel-Access Write command) or after a PIO Read (see Channel- Access Read command). The power-on default function of this pin is RST . 11 P4 I/O pin of channel 4; same characteristics as P0 12 P3 I/O pin of channel 3; same characteristics as P0 13 P2 I/O pin of channel 2; same characteristics as P0 14 P1 I/O pin of channel 1; same characteristics as P0 15 N.C. Not connected 16 N.C. Not connected APPLICATION The DS2408 is a multipurpose device. Typical applications include port expander for microcontrollers, remote multichannel sensor/actuator, communication and control unit of a microterminal, or as network interface of a microcontroller. Typical application circuits and communication examples are found later in this data sheet (Figures 17 to 22). OVERVIEW 5 of 36 Figure 1 shows the relationships between the major function blocks of the DS2408. The device has two main data components: 1) 64-bit lasered ROM, and 2) 64-bit register page of control and status registers. Figure 2 shows the hierarchical structure of the 1-Wire protocol. The bus master must first provide one of the eight ROM function commands: 1) Read ROM, 2) Match ROM, 3) Search ROM, 4) Conditional Search ROM, 5) Skip ROM, 6) Overdrive-Skip ROM, 7) Overdrive-Match ROM, or 8) Resume. Upon completion of an Overdrive ROM command byte executed at standard speed, the device will enter overdrive mode, where all subsequent communication occurs at a higher speed. The protocol required for these ROM function commands is described in Figure 12. After a ROM function command is success- fully executed, the control functions become accessible and the master may provide any one of the five available commands. The protocol for these control commands is described in Figure 8. All data is read and written least significant bit first. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |