| 전자부품 데이터시트 검색엔진 |
|
DS2408S/R 데이터시트(PDF) 11 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
DS2408S/R 데이터시트(HTML) 11 Page - Maxim Integrated Products |
|
11 / 36 page ![]() DS2408 Control/Status Register The data in this register reports status information, determines the function of the RSTZ pin and further configures the device for conditional search. This register can only be written through the Write Condi- tional Search Registers command. Control/Status Register Bitmap ADDR b7 b6 b5 b4 b3 b2 b1 b0 008Dh VCCP 0 0 0 PORL ROS CT PLS This register is read/write. Without VCC supply, this register reads 08h after a power-on reset. The func- tional assignments of the individual bits are explained in the table below. Bits 4 to 6 have no function; they will always read 0 and cannot be set to 1. Control/Status Register Details BIT DESCRIPTION BIT(S) DEFINITION PLS: Pin or Activity Latch Select b0 Selects either the PIO pins or the PIO activity latches as input for the conditional search. 0: pin selected (default) 1: activity latch selected CT: Conditional Search Logical Term b1 Specifies whether the data of two or more channels needs to be OR’ed or AND’ed to meet the qualifying condition for the device to respond to a conditional search. If only a single channel is selected in the channel selection mask (008Bh) this bit is a don't care. 0: bitwise OR (default) 1: bitwise AND ROS: RSTZ Pin Mode Control b2 Configures RSTZ as either RST input or STRB output 0: configured as RST input (default) 1: configured as STRB output PORL: Power-On Reset Latch b3 Specifies whether the device has performed a power-on reset. This bit can only be cleared to 0 under software control. As long as this bit is 1 the device will always respond to a conditional search. VCCP: VCC Power Status (Read-Only) b7 For VCC powered operation the VCC pin needs to be tied to a voltage source ³ VPUP. 0: VCC pin is grounded 1: VCC -powered operation The interaction of the various signals that determine whether the device responds to a conditional search is illustrated in Figure 7. The selection mask SM selects the participating channels. The polarity selection SP determines for each channel whether the channel signal needs to be 1 or 0 to qualify. The PLS bit determines whether all channel signals are taken from the activity latches or I/O pins. The signals of all channels are fed into an AND gate as well as an OR gate. The CT bit finally selects the AND’ed or OR’ed result as the conditional search response signal CSR. Note on CT bit: OR The qualifying condition is met if the input (pin state or activity latch) for one or more selected channels matches the corresponding polarity. AND For the qualifying condition to be met, the input (pin state or activity latch) for every selected channel must match the corresponding polarity. 11 of 36 |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |