전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

DS2408S/R 데이터시트(PDF) 4 Page - Maxim Integrated Products

부품명 DS2408S/R
상세설명  1-Wire 8-Channel Addressable Switch
PDF  36 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  MAXIM [Maxim Integrated Products]
홈페이지  https://www.maximintegrated.com/en.html
Logo MAXIM - Maxim Integrated Products

DS2408S/R 데이터시트(HTML) 4 Page - Maxim Integrated Products

  DS2408S/R Datasheet HTML 1Page - Maxim Integrated Products DS2408S/R Datasheet HTML 2Page - Maxim Integrated Products DS2408S/R Datasheet HTML 3Page - Maxim Integrated Products DS2408S/R Datasheet HTML 4Page - Maxim Integrated Products DS2408S/R Datasheet HTML 5Page - Maxim Integrated Products DS2408S/R Datasheet HTML 6Page - Maxim Integrated Products DS2408S/R Datasheet HTML 7Page - Maxim Integrated Products DS2408S/R Datasheet HTML 8Page - Maxim Integrated Products DS2408S/R Datasheet HTML 9Page - Maxim Integrated Products Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 36 page
background image
DS2408
Note 1:
System Requirement
Note 2:
Maximum allowable pullup resistance is a function of the number of 1-Wire devices in the
system and 1-Wire recovery times. The specified value here applies to systems with only one
device and with the minimum 1-Wire recovery times. For more heavily loaded systems, an
active pullup such as that found in the DS2480B may be required.
Note 3:
If a 2.2k
W resistor is used to pull up the data line to VPUP, 5µs after power has been applied,
the parasite capacitance does not affect normal communications.
Note 4:
Guaranteed by design—not production tested.
Note 5:
VTL, VTH are a function of the internal supply voltage.
Note 6:
Voltage below which, during a falling edge on I/O, a logic '0' is detected.
Note 7:
The voltage on I/O needs to be less or equal to VILMAX whenever the master drives the line
low.
Note 8:
Voltage above which, during a rising edge on I/O, a logic '1' is detected.
Note 9:
After VTH is crossed during a rising edge on I/O, the voltage on I/O has to drop by VHY to be
detected as logic '0'.
Note 10: The I-V characteristic is linear for voltages less than 1V.
Note 11: The earliest recognition of a negative edge is possible at tREH after VTH has been reached
before.
Note 12: Highlighted numbers are NOT in compliance with the published 1-Wire standards. See
comparison table below.
Note 13: Interval during the negative edge on I/O at the beginning of a presence detect pulse between
the time at which the voltage is 90% of VPUP and the time at which the voltage is 10% of
VPUP.
Note 14: e represents the time required for the pullup circuitry to pull the voltage on I/O up from VIL
to VTH.
Note 15: d represents the time required for the pullup circuitry to pull the voltage on I/O up from VIL
to the input high threshold of the bus master.
Note 16: Interval during the device-generated negative edge on any PIO pin or the RSTZ pin between
the time at which the voltage is 90% of VPUP and the time at which the voltage is 10% of
VPUP. PIO pullup resistor = 2.2k
W.
Note 17: Width of the narrowest pulse which trips the activity latch (for any PIO pin) or causes a reset
(for the RSTZ pin). For a pulse duration tPW: If tPW < tPWMIN(min), the pulse will be rejected. If
tPWMIN(min) < tPW < tPWMIN(max), the pulse may or may not be rejected. If tPW > tPWMIN(max) the
pulse will be recognized and latched.
Note 18: Maximum instantaneous pulldown current through all port pins and the RSTZ pin combined.
No requirement for current balance among different pins.
STANDARD VALUES
DS2408 VALUES
STANDARD
SPEED
OVERDRIVE
SPEED
STANDARD
SPEED
OVERDRIVE
SPEED
PARAMETER
NAME
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
tSLOT (incl. tREC)
61µs
(undef.)
7µs
(undef.)
65µs 1)
(undef.)
10µs
(undef.)
tRSTL
480µs
(undef.)
48µs
80µs
660µs
720µs
53µs
80µs
tPDH
15µs
60µs
2µs
6µs
15µs
60µs
2µs
7µs
tPDL
60µs
240µs
8µs
24µs
60µs
280µs
7µs
27µs
tW0L
60µs
120µs
6µs
16µs
60µs
120µs
8µs
13µs
tSLS, tSPD
15µs
60µs
2µs
6µs
15µs
60µs
1.8µs
8µs
1) Intentional change, longer recovery-time requirement due to modified 1-Wire front end.
4 of 36



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com