WM8778SEDSSLASHR datasheet(17/50 Pages) WOLFSON

17 / 50 page

Production Data

WM8778

PD Rev 4.0 April 2005

ADCBCLK and DACBCLK are also generated by the WM8778. The frequency of ADCBCLK and

DACBCLK depends on the mode of operation.

In 128/192fs modes (DACRATE=000 or 001) BCLK = MCLK/2. In 256/384/512fs modes

(ADCRATE/DACRATE=010 or 011 or 100) BCLK = MCLK/4. However if DSP mode is selected as

the audio interface mode then BCLK=MCLK. Note that DSP mode cannot be used in 128fs mode for

word lengths greater than 16 bits or in 192fs mode for word lengths greater than 24 bits.

ZERO DETECT

The WM8778 has a zero detect circuit for each DAC channel, which detects when 1024 consecutive

zero samples have been input. The two zero flag outputs (ZFLAGL and ZFLAGR) may be

programmed to output the zero detect signals (see Table 9) that may then be used to control external

muting circuits. A ‘1’ on ZFLAGL or ZFLAGR indicates a zero detect. The zero detect may also be

used to automatically enable the mute by setting IZD. The zero flag output may be disabled by

setting DZFM to 00.

DZFM[1:0]

ZFLAGL

ZFLAGR

Zero flag disabled

Left channel zero

Right channel zero

Both channel zero

Either channels zero

Either channel zero

Table 9 Zero Flag Output Select

POWERDOWN MODES

The WM8778 has powerdown control bits allowing specific parts of the WM8778 to be powered off

when not being used. Control bit ADCPD powers off the ADC. The ADC input PGAs will be powered

down only if ADCPD and AINPD are set. When AINPD is set the bypass path is automatically

disabled. The stereo DAC has a separate powerdown control bit, DACPD allowing the DAC to be

powered off when not in use. This also switches the analogue outputs VOUTL/R to VMIDDAC to

maintain a dc level on the output. The output mixer will be disabled when PDWN is set.

Setting AINPD, ADCPD and DACPD will powerdown everything except the references VMIDADC,

ADCREF and VMIDDAC. ADCREF and VMIDDAC can be powered down by setting PDWN,

VMIDADC is always active. Setting PDWN will override all other powerdown control bits. It is

recommended that AINPD, ADCPD and DACPD are set before setting PDWN. The default is for all

blocks to be enabled.

DIGITAL AUDIO INTERFACE

MASTER AND SLAVE MODES

The audio interface operates in either Slave or Master mode, selectable using the MS control bit. In

both Master and Slave modes DIN is always an input to the WM8778 and DOUT is always an output.

The default is Slave mode.

In Slave mode (MS=0) ADCLRC, DACLRC, ADCBCLK and DACBCLK are inputs to the WM8778

(Figure 11). DIN and DACLRC are sampled by the WM8778 on the rising edge of DACBCLK,

ADCLRC is sampled on the rising edge of ADCBCLK. ADC data is output on DOUT and changes on

the falling edge of ADCBCLK. By setting control bit BCLKINV the polarity of ADCBCLK and

DACBCLK may be reversed so that DIN and DACLRC are sampled on the falling edge of DACBCLK,

ADCLRC is sampled on the falling edge of ADCBCLK and DOUT changes on the rising edge of

ADCBCLK.

WM8778SEDS/R 데이터시트(PDF) 17 Page - Wolfson Microelectronics plc

WM8778SEDS/R 데이터시트(HTML) 17 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

데이터시트 다운로드

링크 URL