| 전자부품 데이터시트 검색엔진 |
|
MPC8569E 데이터시트(PDF) 103 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC8569E 데이터시트(HTML) 103 Page - Freescale Semiconductor, Inc |
|
103 / 127 page ![]() Enhanced Local Bus Controller MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 1 Freescale Semiconductor 103 2.15.2.2 Enhanced Local Bus AC Timing Specifications for PLL Enable Mode For PLL enable mode, all timings are relative to the rising edge of LSYNC_IN. The following table describes the timing specifications of the enhanced local bus interface at BVDD = 3.3 V, 2.5 V and 1.8 V for PLL enable mode. Table 66. Enhanced Local Bus Timing Specifications (BVDD = 3.3 V 2.5 V and 1.8 V) —PLL Enabled Mode For recommended operating conditions, see Table 3 Parameter Symbol1 Min Max Unit Notes Enhanced local bus cycle time tLBK 7.5 12 ns — Enhanced local bus duty cycle tLBKH/tLBK 45 55 % 5 LCLK[n] skew to LCLK[m] or LSYNC_OUT tLBKSKEW — 680 ps 2 Input setup tLBIVKH 2— ns — Input hold tLBIXKH 1.0 — ns — Output delay (Except LALE) tLBKHOV —3.8 ns — Output hold (Except LALE) tLBKHOX 0.6 — ns — Enhanced local bus clock to output high impedance for LAD/LDP tLBKHOZ —3.8 ns 3 LALE output negation to LAD/LDP output transition (LATCH hold time) tLBONOT 1 – 0.475 ns (LBCR[AHD]=0) ½ – 0.475 ns (LBCR[AHD] = 1) — eLBC controller clock cycle (= 1 platform clock cycle in ns) 4 Notes: 1. All signals are measured from BVDD/2 of the rising edge of LSYNC_IN to BVDD/2 of the signal in question. 2. Skew measured between different LCLK signals at BVDD/2. 3. For purposes of active/float timing measurements, the high impedance or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 4. tLBONOT is a measurement of the minimum time between the negation of LALE and any change in LAD. tLBONOT is determined by LBCR[AHD]. The unit is the eLBC controller clock cycle. The eLBC controller clock refers to the internal clock that runs the local bus controller, not the external LCLK. LCLK cycle = eLBC controller clock cycle × LCRR[CLKDIV]. After power on reset, LBCR[AHD] defaults to 0 and eLBC runs at maximum hold time. 5. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |