| 전자부품 데이터시트 검색엔진 |
|
WM8944BECS/R 데이터시트(PDF) 30 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
WM8944BECS/R 데이터시트(HTML) 30 Page - Cirrus Logic |
|
30 / 165 page ![]() WM8944B 30 Rev 4.3 ADC HIGH PASS FILTER A digital high-pass filter is enabled by default to the ADC path to remove DC offsets. This filter can also be used to remove low frequency noise in handheld applications (e.g. wind noise, handling noise or mechanical vibration). The ADC High Pass filter is enabled by ADC_HPF. Note that this filter must always be set when the Dynamic Range Controller (DRC) is enabled. The DRC will not function correctly if ADC_HPF is not set. The filter operates in one of two modes, selected by ADC_HPF_MODE. The ADC_HPF_SR register should b e set according to the selected ADC sample rate. See “Clocking and Sample Rates ” for details of the ADC sample rate. In Hi-Fi mode (ADC_HPF_MODE = 0), the high-pass filter is optimised for removing DC offsets without degrading the bass response and has a cut-off frequency of 3.5Hz when the sample rate (fs) = 44.1kHz. In Application mode (ADC_HPF_MODE = 1), the HPF cut-off frequency is set using ADC_HPF_CUT. This mode is intended for voice communication; it is recommended to set the cut-off frequency below 300Hz (e.g. ADC_HPF_CUT = 101 when fs = 8kHz or fs = 16kHz). REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R26 (1Ah) ADC Control 2 6 ADC_HPF_MOD E 0 ADC Digital HPF Mode 0 = Hi-Fi mode (1st order) 1 = Application mode (2nd order) 5:4 ADC_HPF_SR [1:0] 10 ADC Digital HPF Sample Rate 00 = 8kHz to 12kHz 01 = 16kHz to 24kHz 10 = 32kHz to 48kHz 11 = Reserved 3:1 ADC_HPF_CUT [2:0] 000 ADC Digital High Pass Filter Cutoff Note that the cut-off frequency scales with sample rate. See Table 11 for cut-off frequencies at all supported sample rates. 0 ADC_HPF 1 ADC Digital High Pass Filter Enable 0 = Disabled 1 = Enabled Table 10 ADC High-pass Filter Control Registers SAMPLE FREQUENCY (kHz) CUT-OFF FREQUENCY (Hz) HI-FI MODE APPLICATION MODE / ADC_HPF_CUT[2:0] 000 001 010 011 100 101 110 111 8.000 3.0 80.5 100.5 129.0 160.5 200.5 256.5 320.5 400.5 11.025 4.5 111.0 138.5 177.5 221.0 276.5 353.0 442.0 551.5 12.000 4.5 120.5 151.0 193.0 240.5 300.5 384.5 481.0 600.5 16.000 3.0 80.0 101.0 129.0 161.0 200.5 256.5 321.0 401.0 22.050 4.5 110.5 139.0 177.5 221.5 276.0 353.5 442.0 552.5 24.000 4.5 120.5 151.5 193.5 241.5 300.5 385.0 481.5 601.0 32.000 2.5 80.0 101.5 129.0 160.5 200.0 257.5 320.0 401.0 44.100 3.5 110.0 139.5 177.5 221.0 275.5 355.0 441.0 552.5 48.000 4.0 119.5 152.0 193.0 240.5 300.0 386.5 480.0 601.0 Table 11 ADC High-pass Filter Cut-off Frequencies Filter response plots for the ADC high-pass filter are shown in “Digital Filter Characteristics”. |
|
링크 URL |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크 투 데이터시트 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |