전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

TIR2000 데이터시트(PDF) 11 Page - Texas Instruments

부품명 TIR2000
상세설명  High-Speed Serial Infrared Controller With 64-Byte FIFO
PDF  63 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  TI [Texas Instruments]
홈페이지  http://www.ti.com
Logo TI - Texas Instruments

TIR2000 데이터시트(HTML) 11 Page - Texas Instruments

Back Button TIR2000 Datasheet HTML 7Page - Texas Instruments TIR2000 Datasheet HTML 8Page - Texas Instruments TIR2000 Datasheet HTML 9Page - Texas Instruments TIR2000 Datasheet HTML 10Page - Texas Instruments TIR2000 Datasheet HTML 11Page - Texas Instruments TIR2000 Datasheet HTML 12Page - Texas Instruments TIR2000 Datasheet HTML 13Page - Texas Instruments TIR2000 Datasheet HTML 14Page - Texas Instruments TIR2000 Datasheet HTML 15Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 11 / 63 page
background image
1–5
1.5
Terminal Functions (Continued)
IRRVL
63
I
Infrared receive. IRRVL is connected to the IR transceiver module and receives data
in the slow-speed mode such as the SIR, Sharp Ir, and TV remote-control modes.
IRTX
62
O
Infrared transmit. IRTX is an output terminal connected to the IR transceiver module
and transmits data out from the TIR2000.
RD
32
I
Read. RD is an active-low signal that indicates when the CPU reads data from the
TIR2000.
RESET
35
I
Reset. When active (high), RESET is used for system reset operation.
RI
57
I
Ring indicator. RI is a modem-status signal. Its condition can be checked by reading
bit 6 (RI) of the MSR. Bit 2 (TERI) of the MSR indicates that RI has transitioned from
a low to a high level since the last read from the MSR. If the modem-status interrupt
is enabled when this transition occurs, an interrupt is generated.
RTS
59
O
Request to send. When low, RTS informs the modem or data set that the ACE is ready
to receive data. RTS is set low by setting the RTS MCR bit and is set to its inactive (high)
level either as a result of a master reset, during loop mode operations, or by clearing
bit 1 (RTS) of the MCR. In the auto-RTS mode, RTS is set low by the receiver threshold
control logic.
SIN
53
I
Serial data. SIN is the input from a connected communications device.
SOUT
58
O
Composite serial data output. SOUT is connected to a communication device. SOUT
is set to the marking (high) level as a result of master reset.
TC
31
I
Terminal count. TC comes from the DMA controller and indicates the end of the block
transfer.
TEST
52
I
Test terminal. TEST is used for test purposes only and should be tied low in normal
operation.
VCC
17, 44,
60
5-V or 3-V supply voltage.
WR
33
I
Write. WR is an active low signal that indicates that the CPU is writing data to the
TIR2000.
Xin, Xout
49, 51
I/O
Crystal connectors. A 48-MHz crystal should be connected across these terminals.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63


데이터시트 다운로드

Go To PDF Page


링크 URL



ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크 투 데이터시트    |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com