ORSPI4 datasheet(84/263 Pages) LATTICE

84 / 263 page

Lattice Semiconductor

ORCA ORSPI4 Data Sheet

• Decrements CALENDAR_M and CALENDAR_LEN counters

• DIP-2 calculation

The core of the RSP block is the state machine shown in Figure 32. The state machine is in the DISABLE state

upon reset. Setting the register bit RX_STATUS_DIS to ‘1’ or misalignment on the SPI4 RX data interface will

cause the state machine to reset to DISABLE state and start sending “11” on the SPI4 status bus. When the

received data is aligned and none of the other conditions apply, the state machine transfers to the SYNC state. The

SYNC state exists for only one clock cycle. In this state the calendar management counters are initialized with the

conﬁgured values from CALENDAR_LEN_RX and CALENDAR_M_RX. The next state is the CAL state if

CALENDAR_SW_EN bit is set to ‘0’ or the SWITCH state if CALENDAR_SW_EN bit is set to ‘1’. In the CAL state,

the counter for CALENDAR_LEN_RX is decremented on each cycle and the counter for CALENDAR_M_RX is

decremented at the end of each calendar sequence. If the CALENDAR_M_RX counter has not reached zero, the

CALENDAR_LEN_RX counter is reset. On each clock cycle, the status is sent out on the RLSTAT bus. The DIP-2

code is calculated in each clock cycle using the method (diagonal XOR) described in the OIF-SPI4-02.0 standard.

Once both calendar management counters have expired, the calendar management is complete and moves to the

DIP-2 state. The current DIP-2 value coming out of the CAL state is XOR’ed with “11”, the ﬁnal 2-bit DIP-2 word is

sent out on the RLSTAT bus and the SYNC state is entered. If the RX_CAL_SW_EN bit is enabled (set to ‘1’) then

the RSP will insert an extra word into the FIFO status frame

Figure 32. RSP State Machine

The SPI4 Receive Status Output (RSO) block contains the low speed LVTTL buffers and LVDS output buffers nec-

essary for the output stage of receive status logic. The option to choose between LVTTL or LVDS outputs is

selected by the software register bit SPI4_STATUS_IO_SEL.

Calendar Programming

On a SPI4 link, FIFO status information is sent periodically over the status link (RSTAT bus on the SPI4 interface)

from the device that receives data. The calendar is a means by which the SPI4 link conveys information to a data

source about the availability of buffer space in the FIFOs that receive data from that data source. A calendar is a

sequence of status messages that

• Provides information on the buffer space for a port or trafﬁc ﬂow

• Allows user to allocate bandwidth for a port or ﬂow depending on the overall trafﬁc characteristics.

DISABLE

SYNC

DIP-2

CAL

SWITCH

RESET

RX_CALENDAR_SW_EN = ‘1’

RX_CALENDAR_SW_EN= “0”

CAL_DONE

RX_CAL_LEN_MAIN/SHD,

RX_CAL_M_MAIN/SHD

DESKEWED

RESET

ORSPI4 데이터시트(PDF) 84 Page - Lattice Semiconductor

ORSPI4 데이터시트(HTML) 84 Page - Lattice Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL