ORSPI4 datasheet(11/263 Pages) LATTICE

11 / 263 page

Lattice Semiconductor

ORCA ORSPI4 Data Sheet

which corresponds to the maximum number of ports that are supported by SPI4. The PDM data is comprised of

three separate segments - a 10-bit dynamic table maintained by the SPI4 logic, a static 20-bit table, and a dynamic

3-bit register ﬁle written by the FIFO Status Update (FSU) logic. The PDM provides a mapping of the SPI4 port

number to the FPGA interface device/port number, removing the burden from FPGA logic.

When port data is read from the PDM, a status update bit (the U-bit) is ﬁrst examined to see whether the STAT ﬁeld

is new or stale. If stale, then the STAT ﬁeld is not considered for the rest of processing. If the STAT ﬁeld is new (U-

bit=1) the STAT ﬁeld is used in conjunction with other ﬁeld to calculate what the new Credit ﬁeld for the port should

be.

A SATISFIED status indicates the corresponding port's FIFO is almost full, and only transfers using the remaining

previously granted 16-byte blocks (if any) may be sent to corresponding port until the next status update. No addi-

tional transfers to that port are permitted.

When a HUNGRY status indication is received, transfers up to MAXBURST2 16-byte blocks or the remainder of

what was previously granted (whichever is greater), may be sent to the corresponding port prior to the next status

update. A STARVING status indication indicates that buffer underﬂow is imminent in the corresponding PHY port.

When STARVING is received, transfers for up to MAXBURST1 16-byte blocks may be sent to the corresponding

port prior to the next status update.

If the U-bit is cleared, this indicates the STAT ﬁeld has already been used to update the Credit ﬁeld on a previous

Port servicing. Therefore, the Credit ﬁeld should simply be reduced by BURST_VAL. Otherwise, the Credit ﬁeld is

updated to the new Credit value minus BURST_VAL. In both cases, the output of the logic is used to update the

Credit ﬁeld. If the Credit ﬁeld is zero, and the STAT ﬁeld is stale, then the port receives no service. Read accesses

of the port control information need to be optimized to minimize any lost bandwidth due to the Credit ﬁeld having a

value of zero.

Data read from the DPRAMS is sent to the SPI4 transmit block which is responsible for the following functions:

• Combining the data and control words from the Transmit FIFO into the data format speciﬁed in the OIF SPI4

standard.

• DIP-4 calculation and insertion into the payload control word.

• Generation of idle/training control words in programmable intervals.

Training words are used to dynamically align the far end receiver. As long as a disabled status ‘11’ is received on

the SPI4 status channel, the transmit interface block sends continuous training patterns (10 training control words

followed by 10 training data words). When valid status is received on the status channel, user data is normally sent

on the SPI4 data link. However, users can also periodically schedule training patterns in TX_DATA_MAX_T peri-

ods. The training patterns can be repeated TX_ALPHA times. Both TX_ALPHA and TX_DATA_MAX_T are pro-

grammable control register bits.

The SPI4 transmit block contains the high-speed serializer which uses the x8 clock, synthesized by an internal

PLL, to generate the high-speed data from the low-speed 128-bit FIFO data. Data is transmitted off-chip using a

16-bit LVDS data bus - TDAT[15:0], a LVDS control bit - TCTL, and a source synchronous clock - TDCLK.

The 16-bit data bus and control are DDR with respect to TDCLK. In order to support 10 Gbits/s throughput, the

minimum frequency of TDCLK needs to be 622 Mbits/s (311 MHz DDR). To allow considerable margin above this

minimum data rate a maximum frequency of operation of 900 Mbits/s is supported.

The Transmit Status Protocol (S4TSP) block provides the interface to the SPI4 Transmit Status interfaces. These

signals can be either LVDS or LVCMOS buffers. The S4TSP block is responsible for the following functions:

• FIFO Status Decoding and Buffering.

• Framing using the status framing pattern.

• DIP-2 checking of incoming status information.

ORSPI4 데이터시트(PDF) 11 Page - Lattice Semiconductor

ORSPI4 데이터시트(HTML) 11 Page - Lattice Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL