MPC8321EVRADDC datasheet(17/82 Pages) FREESCALE

17 / 82 page

MPC8323E PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 4

Freescale Semiconductor

DDR1 and DDR2 SDRAM

MDQ/MDM output setup with respect to MDQS

tDDKHDS,

tDDKLDS

266 MHz

200 MHz

0.9

1.0

—

MDQ/MDM output hold with respect to MDQS

tDDKHDX,

tDDKLDX

266 MHz

200 MHz

1100

1200

—

MDQS preamble start

tDDKHMP

–0.5

× tMCK – 0.6 –0.5 × tMCK +0.6

MDQS epilogue end

tDDKHME

–0.6

0.6

Notes:

1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for

inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing

(DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example,

tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs

(A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference

(K) goes low (L) until data outputs (D) are invalid (X) or data output hold time.

2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.

3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MDM/MDQS. For the ADDR/CMD

setup and hold specifications, it is assumed that the Clock Control register is set to adjust the memory clocks by 1/2 applied

cycle.

4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD)

from the rising edge of the MCK(n) clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control

of the DQSS override bits in the TIMING_CFG_2 register. This is typically set to the same delay as the clock adjust in the

CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same

adjustment value. See the

MPC8323E PowerQUICC II Pro Integrated Communications Processor Reference Manual for a

description and understanding of the timing modifications enabled by use of these bits.

5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), or data

mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor.

6. All outputs are referenced to the rising edge of MCK(n) at the pins of the microprocessor. Note that tDDKHMP follows the

symbol conventions described in note 1.

Table 19. DDR1 and DDR2 SDRAM Output AC Timing Specifications (continued)

At recommended operating conditions with D

n_GVDD of (1.8 or 2.5 V) ± 5%.

Parameter

Symbol1

Min

Max

Unit

Notes

MPC8321EVRADDC 데이터시트(PDF) 17 Page - Freescale Semiconductor, Inc

MPC8321EVRADDC 데이터시트(HTML) 17 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82

데이터시트 다운로드

링크 URL