DSP56364 datasheet(14/148 Pages) FREESCALE

14 / 148 page

Enhanced Serial Audio Interface

DSP56364 Technical Data, Rev. 4.1

2-10

Freescale Semiconductor

PC4

Input, output, or

disconnected

GPIO

disconnected

Port C 4—When the ESAI is configured as GPIO, this signal is individually

programmable as input, output, or internally disconnected.

The default state after reset is GPIO disconnected.

This input is 5 V tolerant.

SCKR

Input or output

GPIO

disconnected

Receiver Serial Clock—SCKR provides the receiver serial bit clock for the

ESAI. The SCKR operates as a clock input or output used by all the enabled

receivers in the asynchronous mode (SYN=0), or as serial flag 0 pin in the

synchronous mode (SYN=1).

When this pin is configured as serial flag pin, its direction is determined by the

RCKD bit in the RCCR register. When configured as the output flag OF0, this

pin will reflect the value of the OF0 bit in the SAICR register, and the data in the

OF0 bit will show up at the pin synchronized to the frame sync in normal mode

or the slot in network mode. When configured as the input flag IF0, the data

value at the pin will be stored in the IF0 bit in the SAISR register, synchronized

by the frame sync in normal mode or the slot in network mode.

PC0

Input, output, or

disconnected

GPIO

disconnected

Port C 0—When the ESAI is configured as GPIO, this signal is individually

programmable as input, output, or internally disconnected.

The default state after reset is GPIO disconnected.

This input is 5 V tolerant.

SCKT

Input or output

GPIO

disconnected

Transmitter Serial Clock—This signal provides the serial bit rate clock for the

ESAI. SCKT is a clock input or output used by all enabled transmitters and

receivers in synchronous mode, or by all enabled transmitters in asynchronous

mode.

PC3

Input, output, or

disconnected

GPIO

disconnected

Port C 3—When the ESAI is configured as GPIO, this signal is individually

programmable as input, output, or internally disconnected.

The default state after reset is GPIO disconnected.

This input is 5 V tolerant.

SDO5

Output

GPIO

disconnected

Serial Data Output 5—When programmed as a transmitter, SDO5 is used to

transmit data from the TX5 serial transmit shift register.

SDI0

Input

GPIO

disconnected

Serial Data Input 0—When programmed as a receiver, SDI0 is used to receive

serial data into the RX0 serial receive shift register.

PC6

Input, output, or

disconnected

GPIO

disconnected

Port C 6—When the ESAI is configured as GPIO, this signal is individually

programmable as input, output, or internally disconnected.

The default state after reset is GPIO disconnected.

This input is 5 V tolerant.

SDO4

Output

GPIO

disconnected

Serial Data Output 4—When programmed as a transmitter, SDO4 is used to

transmit data from the TX4 serial transmit shift register.

Table 2-10 Enhanced Serial Audio Interface Signals (continued)

Signal

Name

Signal Type

State During

Reset

Signal Description

DSP56364 데이터시트(PDF) 14 Page - Freescale Semiconductor, Inc

DSP56364 데이터시트(HTML) 14 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

데이터시트 다운로드

링크 URL